You Timberwolf is a 1994 model.
the 10th number of the vin tells you the year
Here's a table.
10th Character - Year of Manufacture
http://www.kerrywilson.com/vin.htmThis is my vin number to my yamaha timberwolf atv JX44KDA04RA007153, CAN SOMEONE TELL ME THE YEAR PLEASE?
its a 1994
10th character- Identifies the model year. For example: 1988(J), 1989(K), 1990(L), 1991(M), 1992(N), 1993(P), 1994(R), 1995(S), 1996(T),
1997(V), 1998(W), 1999(X), 2000(Y)------2001(1), 2002(2), 2003(3)
Thursday, January 19, 2012
Cheapest place to buy yamaha ATV parts?
if you live in so cal. then go to chaparral motorsportsm they have everything at any timeCheapest place to buy yamaha ATV parts?
it's called e-bay!!Cheapest place to buy yamaha ATV parts?
I have had really good luck at http://www.powerpartsplus.com
The turn around wasn't bad unlike other Yamaha dealers I have ordered from.
it's called e-bay!!Cheapest place to buy yamaha ATV parts?
I have had really good luck at http://www.powerpartsplus.com
The turn around wasn't bad unlike other Yamaha dealers I have ordered from.
So my yamaha warrior atv quad has a piston in it, the guy told me its bored .50 over.. what does that mean?
Does that mean its not a 350 cc anymore? what cc would it be with this bored over?So my yamaha warrior atv quad has a piston in it, the guy told me its bored .50 over.. what does that mean?
the yamaha warrior has a bore and stroke of 83mm x 64.5mm. that means the the hole where you discovered the piston is, is 83mm in diameter. the stroke, or how far the piston travels from top dead center to bottom dead center ( total distance that it moves from top to bottom before it starts to come back up again ) is 64.5mm. using a formula for calculating displacement, it figures out to be 348.98cc or 349cc. If you have it all down correctly, the staing of .5 over would be in millimeters or .020" ( 20 thousanths of an inch ) overbore. that would mean that you now have a bore of 83.5mm calculating out to be a displacement of 353.2cc or 353. If he told you it was bored 50over, he may also be talking inches. .fifty thousandths of an inch convert to 1.27mm so the bore is now 84.27mm. you now have a displacement of 359.74cc or 360cc. Most cylinders, not all, have the capability to be taken to an overbore of .080" or 2mm. Now, did the guy tell you .5mm or 50 over. Little bit of a difference there. Boring isn't to make more power, it's for getting the most use out of your cylinder. Want more power? that's a different question.So my yamaha warrior atv quad has a piston in it, the guy told me its bored .50 over.. what does that mean?
it means that the mechanic bored your cylinder 0.50 (fifty thousandths of an inch) bigger than it was.
mechanics do this to take any scorn marks that have occurred in the engine,the mechanic also does what is refered to as "cross hatching" this is done so that the new piston rings will seat (allow oil to go in the cross hatches reducing heat in the engine,and it also allows the engine to have good compression as well).
with out doing a cross hatch in the cylinder it would cause your piston rings to wear out fast,lower compression ratio,and excessive engine heat which will cause cylinder scoring.
as far as gaining any CC you wouldn't be gaining hardly anything,be that 0.50 is equal to .5 mm you would have to convert the half millimeter to cc,and being that cc is bigger than mm it would be a fraction of a cc.
CHEERS!!!!!!!So my yamaha warrior atv quad has a piston in it, the guy told me its bored .50 over.. what does that mean?
If 4 cylinder, then 350 for real, as they tend to be 348cc as standard. but called 350.
If 2 cylinder. start at 248 and get bored to 249
(that's adding 0.5 to each pston - you can't ust do one or it blows up.)
It means the stock bore is now .050 of an inch bigger in diameter.
the yamaha warrior has a bore and stroke of 83mm x 64.5mm. that means the the hole where you discovered the piston is, is 83mm in diameter. the stroke, or how far the piston travels from top dead center to bottom dead center ( total distance that it moves from top to bottom before it starts to come back up again ) is 64.5mm. using a formula for calculating displacement, it figures out to be 348.98cc or 349cc. If you have it all down correctly, the staing of .5 over would be in millimeters or .020" ( 20 thousanths of an inch ) overbore. that would mean that you now have a bore of 83.5mm calculating out to be a displacement of 353.2cc or 353. If he told you it was bored 50over, he may also be talking inches. .fifty thousandths of an inch convert to 1.27mm so the bore is now 84.27mm. you now have a displacement of 359.74cc or 360cc. Most cylinders, not all, have the capability to be taken to an overbore of .080" or 2mm. Now, did the guy tell you .5mm or 50 over. Little bit of a difference there. Boring isn't to make more power, it's for getting the most use out of your cylinder. Want more power? that's a different question.So my yamaha warrior atv quad has a piston in it, the guy told me its bored .50 over.. what does that mean?
it means that the mechanic bored your cylinder 0.50 (fifty thousandths of an inch) bigger than it was.
mechanics do this to take any scorn marks that have occurred in the engine,the mechanic also does what is refered to as "cross hatching" this is done so that the new piston rings will seat (allow oil to go in the cross hatches reducing heat in the engine,and it also allows the engine to have good compression as well).
with out doing a cross hatch in the cylinder it would cause your piston rings to wear out fast,lower compression ratio,and excessive engine heat which will cause cylinder scoring.
as far as gaining any CC you wouldn't be gaining hardly anything,be that 0.50 is equal to .5 mm you would have to convert the half millimeter to cc,and being that cc is bigger than mm it would be a fraction of a cc.
CHEERS!!!!!!!So my yamaha warrior atv quad has a piston in it, the guy told me its bored .50 over.. what does that mean?
If 4 cylinder, then 350 for real, as they tend to be 348cc as standard. but called 350.
If 2 cylinder. start at 248 and get bored to 249
(that's adding 0.5 to each pston - you can't ust do one or it blows up.)
It means the stock bore is now .050 of an inch bigger in diameter.
What is a Better ATV to choose for Sport use, Honda, Yamaha, Suzuki, or Kawasaki?
I am deciding on a Sport ATV to buy but don't know which company to choose from, I am looking for the best performance and best accessories, your reply will be greatly appreciatedWhat is a Better ATV to choose for Sport use, Honda, Yamaha, Suzuki, or Kawasaki?
Polaris Sportsman 4sureWhat is a Better ATV to choose for Sport use, Honda, Yamaha, Suzuki, or Kawasaki?
Really for sport atvs they all are pretty much the same, i'm not a huge fan of the kawasaki but they have a solid engine. I have a honda 450r and I love it befor that I rode some yamahas. really you cna't go wrong with those 4 brands so just get something you'd think you'd enjoy. I'm not just throwing this crap out i've done lots of research before I buy any atvs and talk to lots of people, I like suzuki I believe they make a damn nice 4 stroke engine. All are fast and performance wise, skys the limit for bolt ons and upgrades. my 450 can now keep up with my buddies 660 raptor.mini countryman
Polaris Sportsman 4sureWhat is a Better ATV to choose for Sport use, Honda, Yamaha, Suzuki, or Kawasaki?
Really for sport atvs they all are pretty much the same, i'm not a huge fan of the kawasaki but they have a solid engine. I have a honda 450r and I love it befor that I rode some yamahas. really you cna't go wrong with those 4 brands so just get something you'd think you'd enjoy. I'm not just throwing this crap out i've done lots of research before I buy any atvs and talk to lots of people, I like suzuki I believe they make a damn nice 4 stroke engine. All are fast and performance wise, skys the limit for bolt ons and upgrades. my 450 can now keep up with my buddies 660 raptor.
Have any ATV mechanics out there to answer why my 1987 yamaha warrior burns oil?
Valve stem worn, valve guide worn, valve stem seal, stuck oil ring on the piston.
If it smokes when you are slowing down it is you valves leaking oil past the guides.
Smokes all of the time it is your rings.
If you can do the over haul or got some one that can do it on the side That motor has replaceable valve guides you can get for $20 each.
If the cylinder wall is worn to bad That will run you $220.
Piston ring set $30
It all come down to is it worth it to you to spend money on it or get some thing different.
The following web site is where I got the prices from. I don't know the availability of the parts.
Good luck.Have any ATV mechanics out there to answer why my 1987 yamaha warrior burns oil?
The piston rings need replacing or the valve guide seals are bad.Have any ATV mechanics out there to answer why my 1987 yamaha warrior burns oil?
The motor is worn!
Hey, 20 years wasn`t bad!
If it smokes when you are slowing down it is you valves leaking oil past the guides.
Smokes all of the time it is your rings.
If you can do the over haul or got some one that can do it on the side That motor has replaceable valve guides you can get for $20 each.
If the cylinder wall is worn to bad That will run you $220.
Piston ring set $30
It all come down to is it worth it to you to spend money on it or get some thing different.
The following web site is where I got the prices from. I don't know the availability of the parts.
Good luck.Have any ATV mechanics out there to answer why my 1987 yamaha warrior burns oil?
The piston rings need replacing or the valve guide seals are bad.Have any ATV mechanics out there to answer why my 1987 yamaha warrior burns oil?
The motor is worn!
Hey, 20 years wasn`t bad!
I HAVE A YAMAHA WOLVERINE ATV. IS THERE ANY OTHER OIL I CAN USE INSTEAD OF YAMALUBE?
THE ENGINE OIL GOES THROUGH THE CLUTCHES SO I NEED A OIL THAT WONT **** UP MY CLUTCHES. ANY IDEAS???I HAVE A YAMAHA WOLVERINE ATV. IS THERE ANY OTHER OIL I CAN USE INSTEAD OF YAMALUBE?
Any SJ-rated 10w40 automotive oil will work. Only the 5w30 and lighter oils have enough friction modifiers to make your clutch slip. Don't waste your money on "motorcycle" oil.I HAVE A YAMAHA WOLVERINE ATV. IS THERE ANY OTHER OIL I CAN USE INSTEAD OF YAMALUBE?
Here is a great site that describes what kind of oil to use in your engine. Basically you need an oil with an API Service category SG or JASO MA. Brand is less important than these service types.
http://www.thumperfaq.com/oil.htmI HAVE A YAMAHA WOLVERINE ATV. IS THERE ANY OTHER OIL I CAN USE INSTEAD OF YAMALUBE?
Valvoline makes a motorcycle oil that can be purchased at any auto part store for about half the price of Yamalube and meets the same requirements. Hope I have been helpful.
Any SJ-rated 10w40 automotive oil will work. Only the 5w30 and lighter oils have enough friction modifiers to make your clutch slip. Don't waste your money on "motorcycle" oil.I HAVE A YAMAHA WOLVERINE ATV. IS THERE ANY OTHER OIL I CAN USE INSTEAD OF YAMALUBE?
Here is a great site that describes what kind of oil to use in your engine. Basically you need an oil with an API Service category SG or JASO MA. Brand is less important than these service types.
http://www.thumperfaq.com/oil.htmI HAVE A YAMAHA WOLVERINE ATV. IS THERE ANY OTHER OIL I CAN USE INSTEAD OF YAMALUBE?
Valvoline makes a motorcycle oil that can be purchased at any auto part store for about half the price of Yamalube and meets the same requirements. Hope I have been helpful.
1993 yamaha atv service manual?
Are there any free publications on this?
Thanks1993 yamaha atv service manual?
Always give year, make, engine size and model # when asking questions. We need all of that info to give an informed answer.
There are lots of free manuals on the web.1993 yamaha atv service manual?
Ask at http://manualfox.com -they find you virtually every manual.
Thanks1993 yamaha atv service manual?
Always give year, make, engine size and model # when asking questions. We need all of that info to give an informed answer.
There are lots of free manuals on the web.1993 yamaha atv service manual?
Ask at http://manualfox.com -they find you virtually every manual.
Need battery for Yamaha 250 ATV year 2000?
This is a list of battery manufactures along with the battery models that are suppose to be used with Yamaha 250cc year 2000:
Power-Sonic - CB14A-A; Yuasa - YB14A-A1 _; Champion -14AA1; GS (JSB) - GM14AZ-4A; GS (ZYI) -CB14A-A ; Motocross - M224A1/ M324A1 ; Napa - 740-1826; Sears - 44056; Staab -14A-A1 (Staab %26amp; Champion the same); GNB - 14AA1 ; Interstate - YB14A-A1 (Yuasa %26amp; Interstate same); GX-Ztong-Yee - CB14A-A ; GX-JSB -GM14AZ-4A ; NAPA - 740-1826 ; Yacht - CB14A-A1 ; Honda - 31500-MXB-019.
With a list of battery manufactures and battery model #s for a Yamaha 250cc ATV yr 2000 looks like there shouldn't be any problem finding a battery. If I buy locally there is a $6 old battery trade in allowance. If I have the battery shipped I would have to buy acid locally to pour into the new battery.
Please tell me the best option.
Thanks!!Need battery for Yamaha 250 ATV year 2000?
Yuasa is the standard for Japanese manufacturers - because they're the best.
The other junk you have listed, won't last half as long.
Sears Die Hard batteries are one of the worst brands.
Buy the battery at your local motorcycle dealer.
They'll fill it with acid, charge it and give you a guarantee.
No department store, or mail order will do that.Need battery for Yamaha 250 ATV year 2000?
Go to Wal*mart. They have a little machine where you can enter your vehicle info and it directs you to the correct battery. I brought my old battery and got like $7.50 back. So it turned out to be $40 minus the $7.50. I took it to Autozone and let them fill it and charge it for free. Advanced Auto Parts does it for free as well.government auctions
Power-Sonic - CB14A-A; Yuasa - YB14A-A1 _; Champion -14AA1; GS (JSB) - GM14AZ-4A; GS (ZYI) -CB14A-A ; Motocross - M224A1/ M324A1 ; Napa - 740-1826; Sears - 44056; Staab -14A-A1 (Staab %26amp; Champion the same); GNB - 14AA1 ; Interstate - YB14A-A1 (Yuasa %26amp; Interstate same); GX-Ztong-Yee - CB14A-A ; GX-JSB -GM14AZ-4A ; NAPA - 740-1826 ; Yacht - CB14A-A1 ; Honda - 31500-MXB-019.
With a list of battery manufactures and battery model #s for a Yamaha 250cc ATV yr 2000 looks like there shouldn't be any problem finding a battery. If I buy locally there is a $6 old battery trade in allowance. If I have the battery shipped I would have to buy acid locally to pour into the new battery.
Please tell me the best option.
Thanks!!Need battery for Yamaha 250 ATV year 2000?
Yuasa is the standard for Japanese manufacturers - because they're the best.
The other junk you have listed, won't last half as long.
Sears Die Hard batteries are one of the worst brands.
Buy the battery at your local motorcycle dealer.
They'll fill it with acid, charge it and give you a guarantee.
No department store, or mail order will do that.Need battery for Yamaha 250 ATV year 2000?
Go to Wal*mart. They have a little machine where you can enter your vehicle info and it directs you to the correct battery. I brought my old battery and got like $7.50 back. So it turned out to be $40 minus the $7.50. I took it to Autozone and let them fill it and charge it for free. Advanced Auto Parts does it for free as well.
Is the 2008 Yamaha grizzly 400 4x4 a good atv?
I want to buy it but is it good, reliable, does it break down, is it fast.Is the 2008 Yamaha grizzly 400 4x4 a good atv?
Great vehicle. This unit would best match up to the Honda Rancher and Polaris Sportsman 400.
Honda Rancher...
4x4 model is only available in electronic shift or semi-automatic. Either way, you have to shift it.
Polaris Sportsman...
Fully automatic and less expensive. Known for chronic belt problems.
Yamaha has a superb name when it comes to toughness, durability, and reliability. With any 4x4 unit an extended warranty is always suggested.
2008 Yamaha Grizzly 400 4WD
Invoice - $4863
Prep - $50
Freight - $216
Hold back - 3% of msrpIs the 2008 Yamaha grizzly 400 4x4 a good atv?
yes, its the best you can get
just don't buy a Polaris
Polaris is soooo junk even the Polaris Dealers refuse to work on them
the reason nobody wants to repair them is because its a losing proposition to repair them cause they break down over and over again and that makes the dealer and the mechanic look bad.
don't believe me? huh? call up any dealer and tell him you have a Polaris ATV and you need a price to fix it, and I bet they will make some excuse or tell you to take it somewhere else.
I mean how pathetic is that?
Polaris dealers don't want to repair their own brand?Is the 2008 Yamaha grizzly 400 4x4 a good atv?
All of the Yamaha 4x4s are good.
Their sport quads require a lot of engine maintenance.
The Grizzly is not made for speed.
Great vehicle. This unit would best match up to the Honda Rancher and Polaris Sportsman 400.
Honda Rancher...
4x4 model is only available in electronic shift or semi-automatic. Either way, you have to shift it.
Polaris Sportsman...
Fully automatic and less expensive. Known for chronic belt problems.
Yamaha has a superb name when it comes to toughness, durability, and reliability. With any 4x4 unit an extended warranty is always suggested.
2008 Yamaha Grizzly 400 4WD
Invoice - $4863
Prep - $50
Freight - $216
Hold back - 3% of msrpIs the 2008 Yamaha grizzly 400 4x4 a good atv?
yes, its the best you can get
just don't buy a Polaris
Polaris is soooo junk even the Polaris Dealers refuse to work on them
the reason nobody wants to repair them is because its a losing proposition to repair them cause they break down over and over again and that makes the dealer and the mechanic look bad.
don't believe me? huh? call up any dealer and tell him you have a Polaris ATV and you need a price to fix it, and I bet they will make some excuse or tell you to take it somewhere else.
I mean how pathetic is that?
Polaris dealers don't want to repair their own brand?Is the 2008 Yamaha grizzly 400 4x4 a good atv?
All of the Yamaha 4x4s are good.
Their sport quads require a lot of engine maintenance.
The Grizzly is not made for speed.
What ATV would you buy between the Suzuki King Quad 750 or the Yamaha Grizzly 700?
I've narrowed my choice to these two ATV's and need some help!What ATV would you buy between the Suzuki King Quad 750 or the Yamaha Grizzly 700?
i love suzuki anything LMAO as long as it's not there carsWhat ATV would you buy between the Suzuki King Quad 750 or the Yamaha Grizzly 700?
neither......don't need training wheels....sorry, i couldn't help myself.
4X4 means 4 times more money to repair.What ATV would you buy between the Suzuki King Quad 750 or the Yamaha Grizzly 700?
grizzly is better, more power, better ground clearance, made tougher, repairs and parts are less expensive.
the only advantage the King Quad has is better gas mileage, but the Suzuki is plagued with electric problems
yamaha is a good machine and will do what you need it to do.
i love suzuki anything LMAO as long as it's not there carsWhat ATV would you buy between the Suzuki King Quad 750 or the Yamaha Grizzly 700?
neither......don't need training wheels....sorry, i couldn't help myself.
4X4 means 4 times more money to repair.What ATV would you buy between the Suzuki King Quad 750 or the Yamaha Grizzly 700?
grizzly is better, more power, better ground clearance, made tougher, repairs and parts are less expensive.
the only advantage the King Quad has is better gas mileage, but the Suzuki is plagued with electric problems
yamaha is a good machine and will do what you need it to do.
Yamaha sport atv, yamaha dirt bike, or kawasaki dirt bike for a 14 year old?
im debating between a 08 yamaha raptor se custom quad, yahmaha tt-r125le dirt bike, or kawasaki klx 140 dirt bike, im 14 and i previously owned a honda dirtbikeYamaha sport atv, yamaha dirt bike, or kawasaki dirt bike for a 14 year old?
kawasaki cause they last along time and go very fast lol 4 stroke tho cause then u can barly ride it if its a 2 stroke cause of the red stickers but ya there great bikes lol i have one and race it and i get 1st,2nd,3rd every time lol
ATV!!!!!
OH I LOVE THEM.
THEY ARE THE BEST THINGS EVER!!!Yamaha sport atv, yamaha dirt bike, or kawasaki dirt bike for a 14 year old?
i like dirtbikes better.
I'd get the Kawasaki DB
I love dirtbikes :D
I have a yamaha.
鈾?it!
Whatever one is going to get you from destination A to destination B safely.Yamaha sport atv, yamaha dirt bike, or kawasaki dirt bike for a 14 year old?
the blaster is a good 200cc quad to have.
Yamaha dirt bike! Well, it really depends on where you live...But atv's are really fun!
The thing about dirt bikes is..you can go more places..You get in a tight spot with only a foot between a big log....The ATV will have to turn around or find away around...You can load it easy into a small truck....You only have to buy 2 tires..
I could go on and on......
ATVs are fun...but!!!
I am not really a fan of quads as I hate to think of the damage they can do when they land on top of the rider. As rough neck has stated you can do so much more on a bike.
i like dirt bikes better so i would have to say the kawasaki. but four wheelers are fun to i have the 08 raptor 700, it is a blast and is fast as hell
kawasaki cause they last along time and go very fast lol 4 stroke tho cause then u can barly ride it if its a 2 stroke cause of the red stickers but ya there great bikes lol i have one and race it and i get 1st,2nd,3rd every time lol
ATV!!!!!
OH I LOVE THEM.
THEY ARE THE BEST THINGS EVER!!!Yamaha sport atv, yamaha dirt bike, or kawasaki dirt bike for a 14 year old?
i like dirtbikes better.
I'd get the Kawasaki DB
I love dirtbikes :D
I have a yamaha.
鈾?it!
Whatever one is going to get you from destination A to destination B safely.Yamaha sport atv, yamaha dirt bike, or kawasaki dirt bike for a 14 year old?
the blaster is a good 200cc quad to have.
Yamaha dirt bike! Well, it really depends on where you live...But atv's are really fun!
The thing about dirt bikes is..you can go more places..You get in a tight spot with only a foot between a big log....The ATV will have to turn around or find away around...You can load it easy into a small truck....You only have to buy 2 tires..
I could go on and on......
ATVs are fun...but!!!
I am not really a fan of quads as I hate to think of the damage they can do when they land on top of the rider. As rough neck has stated you can do so much more on a bike.
i like dirt bikes better so i would have to say the kawasaki. but four wheelers are fun to i have the 08 raptor 700, it is a blast and is fast as hell
Yamaha atv get's boggie?
1990 Yamaha Moto 4 250.When I start's it up it idles fine but when I start to drive it,she boggs out a little bit then takes the gas and repeat's this over and over.Can't be the carburetor because it was just cleaned,adjusted,and a new kit put in it.The choke spring was wore so I temperarily put a pen spring in it.Yamaha atv get's boggie?
pin spring could be sticking, but in my mind the carbs got a dirty jet still, you sure you're getting plenty of gas to the engine? make sure your float level is onpar ;)Yamaha atv get's boggie?
check valves,check carburetor jets,clean air filter
pin spring could be sticking, but in my mind the carbs got a dirty jet still, you sure you're getting plenty of gas to the engine? make sure your float level is onpar ;)Yamaha atv get's boggie?
check valves,check carburetor jets,clean air filter
Yamaha Banshee ATV Jetting?
I have a 04 Yamaha Banshee 350 twin 2 stroke ATV. Starts 2-3 kicks and runs good slow and meduim speeds but when the powerband hits it seems like the throttle sticks or the power won't stop unless you turn the kill switch on. It only does it when it is cold-meduim warmed up and once it gets hot it stops and runs fine. Is it jetted wrong? Is the jetting too lean? I bought it this way and it has Toomey T-6s pipes and clamp-on K%26amp;Ns. Any advice would be appreciated. Thank you!Yamaha Banshee ATV Jetting?
So is it good from 1st thru 3rd shift but then bogs in 4th-6th??
If that the case then its one of three things
1. If it bogs and your spark plug is black and/or wet, use a leaner (smaller) main jet.
2.If performance is very crisp but the motor is popping and the plug is white, go richer (bigger)
BTW: Your plug should be a very light, dry tan color.
3. make sure the choke tube is connected (stock carbs only)
good luck!!acura tsx
So is it good from 1st thru 3rd shift but then bogs in 4th-6th??
If that the case then its one of three things
1. If it bogs and your spark plug is black and/or wet, use a leaner (smaller) main jet.
2.If performance is very crisp but the motor is popping and the plug is white, go richer (bigger)
BTW: Your plug should be a very light, dry tan color.
3. make sure the choke tube is connected (stock carbs only)
good luck!!
Yamaha 1983 atv that wont start?
i have a 83 yamaha it cranks has spark fuel compression it will push start but it takes awhile.when it does push start it will start when you use the electric start.until it cools off. had carb rebuilt. also new batteryYamaha 1983 atv that wont start?
put new plugs in it and check the plug wires and coil also?Yamaha 1983 atv that wont start?
I would get a new plug but that is not the problam this exactley what happends when you need your valves adjusted. I have a Kawasaki Mojave and they notorious for thatYamaha 1983 atv that wont start?
Check the spark timing.
Check the exhaust for clogs
put new plugs in it and check the plug wires and coil also?Yamaha 1983 atv that wont start?
I would get a new plug but that is not the problam this exactley what happends when you need your valves adjusted. I have a Kawasaki Mojave and they notorious for thatYamaha 1983 atv that wont start?
Check the spark timing.
Check the exhaust for clogs
How much oil is needed for an oil change on a 1997 Yamaha big Bear 400 2wd Atv?
about 2 quarts.
i would suggest start measuring the amount of oil after you have put a quart1/2 of oil in it,adding just a little at a time after giving the oil enough time (about 1 min or 2) run down in to the crank case.when you have reached the full mark run the engine for 5 minutes to get the new oil circulated through the new oil filter,and through out the engine,after 5 minutes shut it down.wait for 5 minutes to let oil settle re-check the oil,and add if needed.
best of luck
i would suggest start measuring the amount of oil after you have put a quart1/2 of oil in it,adding just a little at a time after giving the oil enough time (about 1 min or 2) run down in to the crank case.when you have reached the full mark run the engine for 5 minutes to get the new oil circulated through the new oil filter,and through out the engine,after 5 minutes shut it down.wait for 5 minutes to let oil settle re-check the oil,and add if needed.
best of luck
Yamaha atv question. ?
Okay well I have a 1986 yamaha moto 4 250cc. It runs great but it will not idle long at all. It will idle for about 5 seconds and then it will go dead. I have tried to find out how to make it idle on the Internet but I can't. Any help would be appreciated. Thanks. And please be detailed with your answers.Yamaha atv question. ?
sounds like you got something obstructing the idle circuit of carb. remove carb, dissassemble %26amp; clean idle circuit with a very fine piece of wire ( twisttie) or 1 strand of copper fron a piece of auto wire. on the airfilter end of the carb there will be 2 ports before venturi ,1 is larger %26amp; goes to choke circuit, the other is smaller %26amp; bleeds air to idle mixture screw %26amp; upper portion of main jet. be careful not to damage port with a wire that is too thick. I have had this proplem before. it only takes a very small grain of sand or dirt to block the idle mixture port. after reassembly set idle mixture screw at 1.5 turns open, start engine %26amp; fine adjust for smoothest idle that doesn't bog when throttle is opened. check your air filter to ensure it is clean %26amp; sealing correctly to airbox
sounds like you got something obstructing the idle circuit of carb. remove carb, dissassemble %26amp; clean idle circuit with a very fine piece of wire ( twisttie) or 1 strand of copper fron a piece of auto wire. on the airfilter end of the carb there will be 2 ports before venturi ,1 is larger %26amp; goes to choke circuit, the other is smaller %26amp; bleeds air to idle mixture screw %26amp; upper portion of main jet. be careful not to damage port with a wire that is too thick. I have had this proplem before. it only takes a very small grain of sand or dirt to block the idle mixture port. after reassembly set idle mixture screw at 1.5 turns open, start engine %26amp; fine adjust for smoothest idle that doesn't bog when throttle is opened. check your air filter to ensure it is clean %26amp; sealing correctly to airbox
I thought of buying a yamaha raptor atv,but the guy at the store said i can only ride it offroad, why is that?
i didnt get a chance to ask him.
are atvs not street legal or something.?
dont they give licences or permit or whatever for atvs.?I thought of buying a yamaha raptor atv,but the guy at the store said i can only ride it offroad, why is that?
ATVs cannot be plated in most states. I have seen them in Rapid City rush hour traffic however, with South Dakota plates. In Mexico, you see them all over in small towns, sometimes ridden by girls in school uniforms with 2 or 3 passengers.
The U.S. has some funny laws. Since it has 4 wheels instead of 2 or 3 it is considered a car. In order to make it road legal now it would have to be equiped with air bags and meet safety standards. Consequently, motorcycles and trikes have to be open air. If they are completly enclosed then they would be considered a car as well.I thought of buying a yamaha raptor atv,but the guy at the store said i can only ride it offroad, why is that?
just because ya need a license to operate it, dont mean its a street legal vehicle. if ya need a dual purpose vehicle, look around.
Some states will, but there's street legal options that need to be added like turn signals horn and such, I know Utah and I think Montana does.I thought of buying a yamaha raptor atv,but the guy at the store said i can only ride it offroad, why is that?
That is the state law.
are atvs not street legal or something.?
dont they give licences or permit or whatever for atvs.?I thought of buying a yamaha raptor atv,but the guy at the store said i can only ride it offroad, why is that?
ATVs cannot be plated in most states. I have seen them in Rapid City rush hour traffic however, with South Dakota plates. In Mexico, you see them all over in small towns, sometimes ridden by girls in school uniforms with 2 or 3 passengers.
The U.S. has some funny laws. Since it has 4 wheels instead of 2 or 3 it is considered a car. In order to make it road legal now it would have to be equiped with air bags and meet safety standards. Consequently, motorcycles and trikes have to be open air. If they are completly enclosed then they would be considered a car as well.I thought of buying a yamaha raptor atv,but the guy at the store said i can only ride it offroad, why is that?
just because ya need a license to operate it, dont mean its a street legal vehicle. if ya need a dual purpose vehicle, look around.
Some states will, but there's street legal options that need to be added like turn signals horn and such, I know Utah and I think Montana does.I thought of buying a yamaha raptor atv,but the guy at the store said i can only ride it offroad, why is that?
That is the state law.
What Model Yamaha Sport ATV Is This White One?
What Model Yamaha Sport ATV Is This White One?
http://img180.imageshack.us/my.php?image=donkatv15ib6.png
----------------------
Can It Be A Raptor 700R Yamaha Sport ATV
http://img165.imageshack.us/my.php?image=2008raptor700rlv3.png
Or
Can It Be A Raptor 700R SE Yamaha Sport ATV
http://img165.imageshack.us/my.php?image=2008raptor700rlv3.pngWhat Model Yamaha Sport ATV Is This White One?
the raptor 700r and 700se came in blue, white and black/red for some years it's most likly that atv, I doubt it's a 450 but it's deffinatly a raptor.What Model Yamaha Sport ATV Is This White One?
yfz450 would be my guesscalifornia academy of sciences
http://img180.imageshack.us/my.php?image=donkatv15ib6.png
----------------------
Can It Be A Raptor 700R Yamaha Sport ATV
http://img165.imageshack.us/my.php?image=2008raptor700rlv3.png
Or
Can It Be A Raptor 700R SE Yamaha Sport ATV
http://img165.imageshack.us/my.php?image=2008raptor700rlv3.pngWhat Model Yamaha Sport ATV Is This White One?
the raptor 700r and 700se came in blue, white and black/red for some years it's most likly that atv, I doubt it's a 450 but it's deffinatly a raptor.What Model Yamaha Sport ATV Is This White One?
yfz450 would be my guess
I have a yamaha atv with the vin # jy42fh009h0003414 does anyone know what year or model it is. ?
anyone know the modle or year. I think it is a 1987 moto four. it has a 250 cc engine. two wheel drive. thanksI have a yamaha atv with the vin # jy42fh009h0003414 does anyone know what year or model it is. ?
1987 Yamaha YFM200DXT "Moto-4"
The Check Digit in the VIN returns an "INVALID" notice---
I have no idea why.
What it means is that there's an error in one of figures.
It should be what You said ,,except a 200cc not a 250.
Shaft Drive w/reverse,,from SaoPaulo ,Brazil plant
Here's a Owner's manual for an '86,,should be same as '87.
Might be something useful in there
http://www.yamahaownershandbook.com.au/l鈥?/a>I have a yamaha atv with the vin # jy42fh009h0003414 does anyone know what year or model it is. ?
10th digit determines year H i believe was a 1988
1987 Yamaha YFM200DXT "Moto-4"
The Check Digit in the VIN returns an "INVALID" notice---
I have no idea why.
What it means is that there's an error in one of figures.
It should be what You said ,,except a 200cc not a 250.
Shaft Drive w/reverse,,from SaoPaulo ,Brazil plant
Here's a Owner's manual for an '86,,should be same as '87.
Might be something useful in there
http://www.yamahaownershandbook.com.au/l鈥?/a>I have a yamaha atv with the vin # jy42fh009h0003414 does anyone know what year or model it is. ?
10th digit determines year H i believe was a 1988
What is a better ATV? Yamaha raptor 350 or Yamaha banshee
I cant make up my mind on whether i should get a raptor 350 or a banshee. So what is a better atv?What is a better ATV? Yamaha raptor 350 or Yamaha banshee
What type of terrain are you riding on? Also are you an experienced rider or are you a first timer? If you're new to riding go Raptor. Also If you think that these bikes are similar because they have the same displacement your wrong. The Banshee is an awesome bike that has hauled a** ever since it was released back in '86 while the Raptor is more of a beginners bike. If you've ridden before go with the Banshe. Also if you're planning on riding dunes go with the Banshee. But bottom line, Experience=Banshee and Beginner=Raptor 350.
that depends, you want a four stroke or a two stroke?What is a better ATV? Yamaha raptor 350 or Yamaha banshee
raptor 350 looks better
4 stroke less maintennance..... do you like doing maintennace?What is a better ATV? Yamaha raptor 350 or Yamaha banshee
polaris trail blazer or scrambler
remember--yamaha get there yamaha not
raptor
What type of terrain are you riding on? Also are you an experienced rider or are you a first timer? If you're new to riding go Raptor. Also If you think that these bikes are similar because they have the same displacement your wrong. The Banshee is an awesome bike that has hauled a** ever since it was released back in '86 while the Raptor is more of a beginners bike. If you've ridden before go with the Banshe. Also if you're planning on riding dunes go with the Banshee. But bottom line, Experience=Banshee and Beginner=Raptor 350.
that depends, you want a four stroke or a two stroke?What is a better ATV? Yamaha raptor 350 or Yamaha banshee
raptor 350 looks better
4 stroke less maintennance..... do you like doing maintennace?What is a better ATV? Yamaha raptor 350 or Yamaha banshee
polaris trail blazer or scrambler
remember--yamaha get there yamaha not
raptor
What is louder on a yamaha blaster ATV a factory exaust or a cobra exaust?
the loud pipes save lives, if the cobra eexaust has a super trap you can pull that off to make it louder, but the stock pipes are usualy th quietestWhat is louder on a yamaha blaster ATV a factory exaust or a cobra exaust?
Having a loud exhaust is not nice and maybe breaking the law
u must go to jail
Having a loud exhaust is not nice and maybe breaking the law
u must go to jail
What is louder on a yamaha blaster ATV a factory exaust or a cobra exaust?
Having a loud exhaust is not nice and maybe breaking the law
u must go to jail for annoying people and disturbing the peace
ONLY AN IDIOT LAME BRAIN WOULD CHOOSE AN EXHAUST FOR ITS DECIBEL RATING................
GTH
u must go to jail for annoying people and disturbing the peace
ONLY AN IDIOT LAME BRAIN WOULD CHOOSE AN EXHAUST FOR ITS DECIBEL RATING................
GTH
Is Yamaha Big Bear 400 4x4 a relaible atv?
Is it good for plowing, riding, and towing?Is Yamaha Big Bear 400 4x4 a relaible atv?
I think that it is a really nice quad. That thing in first gear with the 4 wheel drive on could climb a mountain. Thing is built like a tank they are great quads.Is Yamaha Big Bear 400 4x4 a relaible atv?
I've worked on many and have never seen any major problems.
Nice quad.vance and hines
I think that it is a really nice quad. That thing in first gear with the 4 wheel drive on could climb a mountain. Thing is built like a tank they are great quads.Is Yamaha Big Bear 400 4x4 a relaible atv?
I've worked on many and have never seen any major problems.
Nice quad.
Whats a better atv for me to buy? a 2003 yamaha raptor 660 or a 2007 polaris outlaw 500? i would rather have a?
outlaw but htere a little more expensive and a little harder to find. it also seems like everyone has a raptor. the outlaw looks better and performs just as well as the raptor 660. please no yamaha or polaris fanboys.Whats a better atv for me to buy? a 2003 yamaha raptor 660 or a 2007 polaris outlaw 500? i would rather have a?
The Yamaha would be best for racing on the track and the Polaris would be better for aggressive trail riding. But they would both do great on either. Just depends on what kind of riding your going to be doing the most. I have a Honda TRX450r and I love it.
The Yamaha would be best for racing on the track and the Polaris would be better for aggressive trail riding. But they would both do great on either. Just depends on what kind of riding your going to be doing the most. I have a Honda TRX450r and I love it.
Who knows a web site to find a free wiring diagram for a 2001 Yamaha ymf350 Wolverine ATV = A four wheeler?
You can use google. com. write down " wiring diagram for 2001 yamaha yfm350 wolverine" they should show on website.
Let me know if you cant find. I will check it out for you.
ToddWho knows a web site to find a free wiring diagram for a 2001 Yamaha ymf350 Wolverine ATV = A four wheeler?
check the yamaha website , they may have something on it in the customer section
Let me know if you cant find. I will check it out for you.
ToddWho knows a web site to find a free wiring diagram for a 2001 Yamaha ymf350 Wolverine ATV = A four wheeler?
check the yamaha website , they may have something on it in the customer section
I am looking to purchase a Yamaha Grizzly 450 4X4 ATV is this a good working ATV?
I have found the ATV I want to purchase I can get it for $1000 less at Abernathy cycles in Union City Tn. But Im just needing to know if the Yamaha 450 Grizzly is a good purchase for the Camo Outdoorsman Edition it is $5800 that includes gun scaberd mud flaps and Bag for the Back rack. I have never drivin a yamaha 4 wheeler I have rode a Honda Forman but I dont like having to manually shift gears.; any advice will help thanksI am looking to purchase a Yamaha Grizzly 450 4X4 ATV is this a good working ATV?
yes it is a good 4 wheeler it is strong and reliable to work with also if you need it to do other work like on a ranch or hauling loads it will not let you down you can buy aftermarket ***. for it as well IE trailer plows things of that nature also if you just want a hunting four wheeler it is a real real good woods 4 wheeler buy it you will not be disappointed in it but a little advise when hunting buy a silencer for it that quiets it down more than stock because we don't want the animals smell and hearing us coming in to the woods... will give you lasting life if it is well maintained so go buy it and enjoy itI am looking to purchase a Yamaha Grizzly 450 4X4 ATV is this a good working ATV?
Yammies are pretty good and very reliable, A couple of my mates have Yammies (sports quads) and they have never had any problems with them.I am looking to purchase a Yamaha Grizzly 450 4X4 ATV is this a good working ATV?
If you want my two cents. If you are after a good deal on a utility atv with a hunting package. Go with the kawasaki prarie 700. You can get it for just about the same price as you are talking about. It has crazy power and it is totally automatic. Great atv. My parents have 2 of them they use for mudding. I personally like my yamaha tri-z 250 3 wheeler, but I have always been into sand dune riding. All atvs are fun though. Enjoy when you get one.
All I can say is that I have a YAM 400 Kodiak(I think the Grizzly is a 650)I beat the hell out of it in really rugged terrain in NH and it goes anywhere and nothing but minor quick fixes ever needed.I will guess that TN conditions will be similar to us north country riders(BIG mud,steep hills)It has proven to be a great choice for me.My nephews Honda foreman is OK but i lose him in the dust and he seems to need more repairs!
yes it is a good 4 wheeler it is strong and reliable to work with also if you need it to do other work like on a ranch or hauling loads it will not let you down you can buy aftermarket ***. for it as well IE trailer plows things of that nature also if you just want a hunting four wheeler it is a real real good woods 4 wheeler buy it you will not be disappointed in it but a little advise when hunting buy a silencer for it that quiets it down more than stock because we don't want the animals smell and hearing us coming in to the woods... will give you lasting life if it is well maintained so go buy it and enjoy itI am looking to purchase a Yamaha Grizzly 450 4X4 ATV is this a good working ATV?
Yammies are pretty good and very reliable, A couple of my mates have Yammies (sports quads) and they have never had any problems with them.I am looking to purchase a Yamaha Grizzly 450 4X4 ATV is this a good working ATV?
If you want my two cents. If you are after a good deal on a utility atv with a hunting package. Go with the kawasaki prarie 700. You can get it for just about the same price as you are talking about. It has crazy power and it is totally automatic. Great atv. My parents have 2 of them they use for mudding. I personally like my yamaha tri-z 250 3 wheeler, but I have always been into sand dune riding. All atvs are fun though. Enjoy when you get one.
All I can say is that I have a YAM 400 Kodiak(I think the Grizzly is a 650)I beat the hell out of it in really rugged terrain in NH and it goes anywhere and nothing but minor quick fixes ever needed.I will guess that TN conditions will be similar to us north country riders(BIG mud,steep hills)It has proven to be a great choice for me.My nephews Honda foreman is OK but i lose him in the dust and he seems to need more repairs!
Yamaha Warrior 350 ATV where can I find one?
I need a webite that will give me a price to print out for a 350 yamaha warriorYamaha Warrior 350 ATV where can I find one?
This is the company that most of my area dealers use to get their prices on used machines.
http://www.nadaguides.com/
For new machines just go to the manufactures websites %26amp; they usually have the suggested list price posted. But hopefully you will find one that sells the machine for under that price.Yamaha Warrior 350 ATV where can I find one?
www.traderonline.com
www.ebay.com
This is the company that most of my area dealers use to get their prices on used machines.
http://www.nadaguides.com/
For new machines just go to the manufactures websites %26amp; they usually have the suggested list price posted. But hopefully you will find one that sells the machine for under that price.Yamaha Warrior 350 ATV where can I find one?
www.traderonline.com
www.ebay.com
What's a faster atv, a suzuki 400 or a Yamaha yfz450?
My friend has both a 2003 yfz450 and a 2004 Suzuki 400, although the 400 has a 440 kit in it. To make a long story short he can't tell which one is faster. So basically which one should be faster?What's a faster atv, a suzuki 400 or a Yamaha yfz450?
power to weight ratio ... drag them and findout ( try to have equal weight riders ) the yamaha should be fasterWhat's a faster atv, a suzuki 400 or a Yamaha yfz450?
im not a Genius on atvs but overall the Yamaha has 10cc higher power but the power to rate ratio would mean that the suzuki 400 would be fasterWhat's a faster atv, a suzuki 400 or a Yamaha yfz450?
Neither is considered "Fast".
Yawnmopar
power to weight ratio ... drag them and findout ( try to have equal weight riders ) the yamaha should be fasterWhat's a faster atv, a suzuki 400 or a Yamaha yfz450?
im not a Genius on atvs but overall the Yamaha has 10cc higher power but the power to rate ratio would mean that the suzuki 400 would be fasterWhat's a faster atv, a suzuki 400 or a Yamaha yfz450?
Neither is considered "Fast".
Yawn
Smoke coming out of pull start on atv?
On my 96' yamaha atv engine after riding for an hour or so there is white smoke coming out of the plate which the pull start is connected to right beside the gear selector foot thingy...what does this mean?
There is no clutch on this model you just kick up to switch gears.Smoke coming out of pull start on atv?
Something is seizing up. Take it in and have it looked at if you don't you can damage the engine.
There is no clutch on this model you just kick up to switch gears.Smoke coming out of pull start on atv?
Something is seizing up. Take it in and have it looked at if you don't you can damage the engine.
Is the Yamaha banshee a good FAST ATV?
i want a fast ATV and i like the banshee's but i don't know whether to get a two stroke are they too much work? will i spend more time working on it than being able to ride?Is the Yamaha banshee a good FAST ATV?
Work great but a lot of money to maintain.
Great atv just hope you like working on it
Work great but a lot of money to maintain.
Great atv just hope you like working on it
DO THEY SELL YAMAHA, ATV'S,DIRT BIKES,JET SKI'S,AND BOATS,ALL YAMAHA BRAND IN ACAPULCO,MEXICO?
IM MOVING TO ACAPULCODO THEY SELL YAMAHA, ATV'S,DIRT BIKES,JET SKI'S,AND BOATS,ALL YAMAHA BRAND IN ACAPULCO,MEXICO?
Yes they do. There are honda stores and Yamaha Stores. There are also a few stores that sell different brands.
Yes they do. There are honda stores and Yamaha Stores. There are also a few stores that sell different brands.
Best Big Utility ATV, Yamaha Grizzly, Suzuki King Quad, or Kawasaki Brute Force?
The Yamaha Grizzly is 700cc, and the Suzuki and Kawasaki is 750cc
What one is the best and why?
I was reading the reviews and the only one that got bad reviews was the Kawasaki Brute Force with engine oil leaks, engine knocks and high oil consumption problems, is this true or are these manufactured lies made up by Kawasaki Haters?Best Big Utility ATV, Yamaha Grizzly, Suzuki King Quad, or Kawasaki Brute Force?
Kawasaki is a tough quad, but the dealers ive dealt with dont stand behind what they sell. I would go with the grizzly, that is one tough four wheeler!!Best Big Utility ATV, Yamaha Grizzly, Suzuki King Quad, or Kawasaki Brute Force?
I would choose the Yamaha Grizzly.
Yamaha work quads are tried and true, strong build and quality (I wouldn't say that about their race quads).
Kawasaki quads have been having problems ever since the Prairie models came out.
What one is the best and why?
I was reading the reviews and the only one that got bad reviews was the Kawasaki Brute Force with engine oil leaks, engine knocks and high oil consumption problems, is this true or are these manufactured lies made up by Kawasaki Haters?Best Big Utility ATV, Yamaha Grizzly, Suzuki King Quad, or Kawasaki Brute Force?
Kawasaki is a tough quad, but the dealers ive dealt with dont stand behind what they sell. I would go with the grizzly, that is one tough four wheeler!!Best Big Utility ATV, Yamaha Grizzly, Suzuki King Quad, or Kawasaki Brute Force?
I would choose the Yamaha Grizzly.
Yamaha work quads are tried and true, strong build and quality (I wouldn't say that about their race quads).
Kawasaki quads have been having problems ever since the Prairie models came out.
Yamaha Warrior??? ATV?
I am thinking of purchasing a 98 yamaha warrior 350 atv. can anyone give me some reviews and opinions of this quad?Yamaha Warrior??? ATV?
hey, warrior's are amazing quads. I've got a 92 and i've never had a single problem.
they perform the best on the trails, but they're quite capable of racing to! their engine layout is really simple, so their easy to fix. by all means, go for it, though the only thing about warrior's is that in time they develope a "tick" in the top end. It's nothing to worry about, it can simply be fixed by tightening the timing chain.
if you want an actual review check out this link:
http://www.motorcycle.com/mo/mcyam/97warrior.htmlelectric car
hey, warrior's are amazing quads. I've got a 92 and i've never had a single problem.
they perform the best on the trails, but they're quite capable of racing to! their engine layout is really simple, so their easy to fix. by all means, go for it, though the only thing about warrior's is that in time they develope a "tick" in the top end. It's nothing to worry about, it can simply be fixed by tightening the timing chain.
if you want an actual review check out this link:
http://www.motorcycle.com/mo/mcyam/97warrior.html
I am looking for ATV crate engines. I am rebuilding an 88 yamaha warrior and would like to get a new engine.?
The engine that is in it has been rebuilt before and I am doing a frame off resto so I would like to put a new engine in it. I have found many engines on ebay but the are also used. I would consider going with a larger cc if it was out of a Yamaha.I am looking for ATV crate engines. I am rebuilding an 88 yamaha warrior and would like to get a new engine.?
they dont make/sell whole engines for these or any japanese bikes/quads. you can buy all the parts new, cases, piston, head, cylinder cam etc. but you or a mechanic will have to put it together. rebuild the old on and get the new exterior parts, covers cases etc. and it will look new.
they dont make/sell whole engines for these or any japanese bikes/quads. you can buy all the parts new, cases, piston, head, cylinder cam etc. but you or a mechanic will have to put it together. rebuild the old on and get the new exterior parts, covers cases etc. and it will look new.
(ATV)-Yamaha Warrior 350cc Engine in pecies..(DESCRIPTION)!.?
Hi there, i bought an ATV yamaha warrior 350cc but i don't know thee year.. the only thing missing is the engine well sort of... I have the engine but in piecies every piece is separated from the complete engine.. I have all the pieces, so can you help me?! I don't really have money for garage.. i want to maybe check videos or the steps for rebuilding it.... PLease give me advices..!
Patrick Ch.(ATV)-Yamaha Warrior 350cc Engine in pecies..(DESCRIPTION)!.?
You should be able to buy a service manual and it will tell you exactly how it all goes together with pictures and schematics. Make sure you use all new gaskets and seals. Why was it all apart? This throws up a red flag to me. Anyways a manual may be upwards of $100 but it's cheaper than the labor to have a shop do it, plus you'll gain a lot of knowledge of how the engine works if you do it yourself. You'll need a large, clean work bench to do it but it isn't that difficult. Take your time and relax, and enjoy doing it.
Patrick Ch.(ATV)-Yamaha Warrior 350cc Engine in pecies..(DESCRIPTION)!.?
You should be able to buy a service manual and it will tell you exactly how it all goes together with pictures and schematics. Make sure you use all new gaskets and seals. Why was it all apart? This throws up a red flag to me. Anyways a manual may be upwards of $100 but it's cheaper than the labor to have a shop do it, plus you'll gain a lot of knowledge of how the engine works if you do it yourself. You'll need a large, clean work bench to do it but it isn't that difficult. Take your time and relax, and enjoy doing it.
Could I find a used/older model ATV at a Yamaha dealership?
The new ones are a little bit out of my price range so I was wondering if I could go there and get a used older model, or a new older model.Could I find a used/older model ATV at a Yamaha dealership?
Yes, dealers will usually carry used bikes and many have non-current year new bikes also.
Yes, dealers will usually carry used bikes and many have non-current year new bikes also.
2001 yamaha warrior 350 atv wont stay running?
I have a 2001 yamaha warrior it will start but then backfires and stalls . i have put on a new stator pulsar coil ,cdi box, cam chain,valves,carb is clean and has no issues the time lite says its firing when it should what is causing my atv to not run pleaaase help with any ideas also all woodruff keys are good and not broke2001 yamaha warrior 350 atv wont stay running?
More info would be helpful - how long will it run, does if stall after reving the engine, stall after taking off choke , explicit details.
Check the parking brake switch.
When the parking brake is applied, it activates a rev limiter to prevent burning up the brakes %26amp; clutch when trying to ride with the parking brake on.
If the switch was not working properly, the rev limiter would be on always, causing the engine to misfire constantly.
The parking brake switch is at the left handlebar lever.2001 yamaha warrior 350 atv wont stay running?
Try a really good spark plug alot of times they are burnt or have alot of gas on them my cr 125 did the same thing checked everything and ended up being a foul plug got a new one and kicked right over and idled great! Hope this helped.
More info would be helpful - how long will it run, does if stall after reving the engine, stall after taking off choke , explicit details.
Check the parking brake switch.
When the parking brake is applied, it activates a rev limiter to prevent burning up the brakes %26amp; clutch when trying to ride with the parking brake on.
If the switch was not working properly, the rev limiter would be on always, causing the engine to misfire constantly.
The parking brake switch is at the left handlebar lever.2001 yamaha warrior 350 atv wont stay running?
Try a really good spark plug alot of times they are burnt or have alot of gas on them my cr 125 did the same thing checked everything and ended up being a foul plug got a new one and kicked right over and idled great! Hope this helped.
Thursday, January 12, 2012
Does anyone know whats wrong when a 2001 yamaha warrior ATV 4-wheeler that won't start.?
I press the start button and all it does is click like the battery is dead but the battery is not dead i have charged it, i can also pull start it with another 4-wheeler. so if you have any ideas please let me know thanksDoes anyone know whats wrong when a 2001 yamaha warrior ATV 4-wheeler that won't start.?
The first answer is correct, however, you say that it will run if you pull start it so you do not need any of that info. The clicking sound you hear is no doubt the starter solenoid which is USUALLY a sign of a weak battery. Just because you charged the battery doesn't mean that it is good. If you don't want to buy another battery, borrow one, or use jumper cables from your car (hook them up correctly and don't start the car). If it starts the battery is your problem, if it still will not turn over, then, it may be your solenoid or the starter motor itself. For further testing, run a jumper cable from +battery right to the large wire connection on the starter motor (assuming good battery and good ground) if it cranks the engine starter motor is good, if it doesn't crank its bad. Hope this info helps.Does anyone know whats wrong when a 2001 yamaha warrior ATV 4-wheeler that won't start.?
you need four things for a motor to start - gas, air, spark, and timing. im sure the timing in the motor is fine, so that leaves air, gas and spark. also, air is almost always getting to the engine so ignore checking that. spark - remove the spark plug and place it back in the spark plug wire. ground the threads of the plug on the block and crank the motor. if you see a spark (its usually very faint) or you get shocked, the spark is fine. as for fuel, i cant think of an easy way to check other than removing the spark plug and turning on the gas valve and cranking the motor. fuel should spray out of the spark plug hole a little when you crank it over.Does anyone know whats wrong when a 2001 yamaha warrior ATV 4-wheeler that won't start.?
check battery connections.kuryakyn
The first answer is correct, however, you say that it will run if you pull start it so you do not need any of that info. The clicking sound you hear is no doubt the starter solenoid which is USUALLY a sign of a weak battery. Just because you charged the battery doesn't mean that it is good. If you don't want to buy another battery, borrow one, or use jumper cables from your car (hook them up correctly and don't start the car). If it starts the battery is your problem, if it still will not turn over, then, it may be your solenoid or the starter motor itself. For further testing, run a jumper cable from +battery right to the large wire connection on the starter motor (assuming good battery and good ground) if it cranks the engine starter motor is good, if it doesn't crank its bad. Hope this info helps.Does anyone know whats wrong when a 2001 yamaha warrior ATV 4-wheeler that won't start.?
you need four things for a motor to start - gas, air, spark, and timing. im sure the timing in the motor is fine, so that leaves air, gas and spark. also, air is almost always getting to the engine so ignore checking that. spark - remove the spark plug and place it back in the spark plug wire. ground the threads of the plug on the block and crank the motor. if you see a spark (its usually very faint) or you get shocked, the spark is fine. as for fuel, i cant think of an easy way to check other than removing the spark plug and turning on the gas valve and cranking the motor. fuel should spray out of the spark plug hole a little when you crank it over.Does anyone know whats wrong when a 2001 yamaha warrior ATV 4-wheeler that won't start.?
check battery connections.
Is a 2002 yamaha big bear 400 4x4 a good atv?
Is it reliable? Is it good for towing a yard trailer, riding, and plowing. Does it break often?Is a 2002 yamaha big bear 400 4x4 a good atv?
Yamaha makes a good strong atv. It'll handle anything you throw at it.Is a 2002 yamaha big bear 400 4x4 a good atv?
We've had ours since 2002 and that only thing that has been replaced is the shock (only because it was worn out making the ride bouncy). I take it out almost every weekend their great going through water no snorkel or and modifications and I've had water over the seat multiply times. I use mine for mudding/ridding. Best atv I ever owned. When this one does die(which looks like won't be for a while) I'll defiantly buy another one.
Yamaha makes a good strong atv. It'll handle anything you throw at it.Is a 2002 yamaha big bear 400 4x4 a good atv?
We've had ours since 2002 and that only thing that has been replaced is the shock (only because it was worn out making the ride bouncy). I take it out almost every weekend their great going through water no snorkel or and modifications and I've had water over the seat multiply times. I use mine for mudding/ridding. Best atv I ever owned. When this one does die(which looks like won't be for a while) I'll defiantly buy another one.
What is the difference between these Yamaha ATVs?
I have the choice of buying a normal 2008 Yamaha Raptor 250, a Yamaha Raptor 250 SE, or a Yamaha Raptor 250 SE Custom,,,, What is the difference between these 3 atvs.. Pros and cons please and any other detailsWhat is the difference between these Yamaha ATVs?
different style differnet suspension and tire size along with options along with motor optionsWhat is the difference between these Yamaha ATVs?
different seat heights engines build differntly front tire bigger/smaller ones for racing..
different style differnet suspension and tire size along with options along with motor optionsWhat is the difference between these Yamaha ATVs?
different seat heights engines build differntly front tire bigger/smaller ones for racing..
ATV How fast does a yamaha blaster go?
Whats the top speed of a 2000 stock yamaha blaster
also how much faster would it go if it had a pipe and silences, reeds, and a jetkitATV How fast does a yamaha blaster go?
stock about 45 mph which is slow but good speed for a 200cc engine. All those upgrades giving good conditions you're looking at probably another 10-15 mph which is great. I rode a upgrade blaster and that thing really whips around good I would buy one but i'm just to tall to sit on it all day. The guy I knew had one with the pipe and jet upgrades and it kept up with but not as fast as my honda 450r which was stock at the time, his was a 98 pretty much the same as a 2000. There are more upgrades you can do...upgrade the cam, pollish the head, change the air filter to K%26amp;N, and you're looking at a very fast fun machine.ATV How fast does a yamaha blaster go?
thats bull, i hav one that has just a little engine work, nothin special at all, it may not hav even made a diffence and it goes 65
livewire may be a top contributor but thats bull **** what he says. he is a lier
ok on a stock 2000 blaster by gps i have had my blaster up to 59 with 230 on it so i know i could be faster
also how much faster would it go if it had a pipe and silences, reeds, and a jetkitATV How fast does a yamaha blaster go?
stock about 45 mph which is slow but good speed for a 200cc engine. All those upgrades giving good conditions you're looking at probably another 10-15 mph which is great. I rode a upgrade blaster and that thing really whips around good I would buy one but i'm just to tall to sit on it all day. The guy I knew had one with the pipe and jet upgrades and it kept up with but not as fast as my honda 450r which was stock at the time, his was a 98 pretty much the same as a 2000. There are more upgrades you can do...upgrade the cam, pollish the head, change the air filter to K%26amp;N, and you're looking at a very fast fun machine.ATV How fast does a yamaha blaster go?
thats bull, i hav one that has just a little engine work, nothin special at all, it may not hav even made a diffence and it goes 65
Report Abuse
ATV How fast does a yamaha blaster go?livewire may be a top contributor but thats bull **** what he says. he is a lier
Report Abuse
ok on a stock 2000 blaster by gps i have had my blaster up to 59 with 230 on it so i know i could be faster
Report Abuse
What is the 0-60 time on a stock 2005 Yamaha raptor 700 atv and a stock 2005 Yamaha YFZ450 atv?
Obviously, the 700 would be quicker. I can't give you exact numbers tho. I can tell you that 60mph on a quad feels like 120mph, and they are not designed to be ridden that fast.What is the 0-60 time on a stock 2005 Yamaha raptor 700 atv and a stock 2005 Yamaha YFZ450 atv?
This is a response to a 1 answer question over 30 days old.
I hope you will find what you are looking for.
These are the best answer links I know.
Check them out and if you still need help feel free
to Email me for help, supergwo@Yahoo.com.
http://www.ask.com/?o=312#subject:ask|pg鈥?/a> - everything
http://www.info.com/ - 14 search engines
http://www.wisegeek.com/ - any question
http://www.autozone.com/ - diagrams,repair info,LOOK HERE
http://autoparts.411web.com/ - everything automotive
http://www.howstuffworks.com/ - how stuff works
http://www.thefreedictionary.com/ - dictionary
http://www.2carpros.com/index.htm - mechanics Q %26amp; A
http://www.streetracing.org/paris/dictio鈥?/a> - terms
http://www.crutchfieldadvisor.com/S-CHQL鈥?/a> - automotive audio/video etc.
http://www.partstrain.com/?id=doMecGRr - hard to find parts
http://www.mapquest.com/directions/ - directions %26amp; distance
http://www.carcarecouncil.org/index.shtm鈥?/a> - basic car care
http://www.diynetwork.com/diy/autos_boat鈥?/a> - DIY resource
http://www.autospeak.com/index.htm - for car enthusiasts
http://www.mendmy.com/answers.php?id=139鈥?/a> - fix anything
http://www.theautochannel.com/ - up to date auto news
http://www.motorera.com/ - old cars %26amp; definitions
http://www.autopedia.com/ - automotive dictionary
http://www.edmunds.com/ - automotive values
http://sd.craigslist.org/about/cities.ht鈥?/a> - community classifieds
http://www.nhtsa.dot.gov/ - Nat'l Hyway Traffic Safety Admin.
Web search for Forums for your car, they are very helpful.
Fereral, State, %26amp; Local governments have websites.
Go to my 360 site to read my blogs.
This is a response to a 1 answer question over 30 days old.
I hope you will find what you are looking for.
These are the best answer links I know.
Check them out and if you still need help feel free
to Email me for help, supergwo@Yahoo.com.
http://www.ask.com/?o=312#subject:ask|pg鈥?/a> - everything
http://www.info.com/ - 14 search engines
http://www.wisegeek.com/ - any question
http://www.autozone.com/ - diagrams,repair info,LOOK HERE
http://autoparts.411web.com/ - everything automotive
http://www.howstuffworks.com/ - how stuff works
http://www.thefreedictionary.com/ - dictionary
http://www.2carpros.com/index.htm - mechanics Q %26amp; A
http://www.streetracing.org/paris/dictio鈥?/a> - terms
http://www.crutchfieldadvisor.com/S-CHQL鈥?/a> - automotive audio/video etc.
http://www.partstrain.com/?id=doMecGRr - hard to find parts
http://www.mapquest.com/directions/ - directions %26amp; distance
http://www.carcarecouncil.org/index.shtm鈥?/a> - basic car care
http://www.diynetwork.com/diy/autos_boat鈥?/a> - DIY resource
http://www.autospeak.com/index.htm - for car enthusiasts
http://www.mendmy.com/answers.php?id=139鈥?/a> - fix anything
http://www.theautochannel.com/ - up to date auto news
http://www.motorera.com/ - old cars %26amp; definitions
http://www.autopedia.com/ - automotive dictionary
http://www.edmunds.com/ - automotive values
http://sd.craigslist.org/about/cities.ht鈥?/a> - community classifieds
http://www.nhtsa.dot.gov/ - Nat'l Hyway Traffic Safety Admin.
Web search for Forums for your car, they are very helpful.
Fereral, State, %26amp; Local governments have websites.
Go to my 360 site to read my blogs.
Ideas on getting a CDI box for an ATV 1988 Yamaha YFM 350 ERU Moto-4 that isn't $500 from Yamaha..?
I am looking for this CDI box and it is extremely hard to find...Can not find one on Ebay or anywhere else...Have found at Yamaha but it is $500 and the ATV isn't worth that....Any other models or years that might match this CDI box that I could find? Help please....Ideas on getting a CDI box for an ATV 1988 Yamaha YFM 350 ERU Moto-4 that isn't $500 from Yamaha..?
Heres what I recommend:
1)check local phone book for "motorcycle salvage yard"
2)go to it and take the bad module with you.
Chances are it can be matched up with something there. Or at least call them on the phone and ask.
If they don't have it, then do a web search for motorcycle salvage yards and enter exactly what you have. In the comments sections, make sure to put something like "please no stock "we have your part" answers as I want the price as well as availability". Seems some salvage yards use a generic email answer that is pure b.s. They may not have the part, but indicate they do. They also don't list the cost. So be honest up front with the salvage yards and they will be honest with you. The only problem is that you must be certain that the unit is good before installing it. I always test used parts before installing them, and inform the salvage yards that I will be testing the part before it is installed, and if it fails any of the tests it will be exchanged. Give no nonsense and take none. Perhaps I can get away with it because I operate a repair shop, but if you treat buisness people with respect it shows you mean buisness.carolina skiff
Heres what I recommend:
1)check local phone book for "motorcycle salvage yard"
2)go to it and take the bad module with you.
Chances are it can be matched up with something there. Or at least call them on the phone and ask.
If they don't have it, then do a web search for motorcycle salvage yards and enter exactly what you have. In the comments sections, make sure to put something like "please no stock "we have your part" answers as I want the price as well as availability". Seems some salvage yards use a generic email answer that is pure b.s. They may not have the part, but indicate they do. They also don't list the cost. So be honest up front with the salvage yards and they will be honest with you. The only problem is that you must be certain that the unit is good before installing it. I always test used parts before installing them, and inform the salvage yards that I will be testing the part before it is installed, and if it fails any of the tests it will be exchanged. Give no nonsense and take none. Perhaps I can get away with it because I operate a repair shop, but if you treat buisness people with respect it shows you mean buisness.
Anyone Got Yamaha ATV Tires?
Does anyone have a set of new tires for a 2002 yamaha bear tracker? It has 22x7x10 on the front and 22x10x10 on the rear. I would like to have 23's or 24's but 22's will work? If so let me know what kinda and a price.Anyone Got Yamaha ATV Tires?
This isn't ebay buddy, go to a tire shop in your area it will be way cheaperAnyone Got Yamaha ATV Tires?
IF you are rural and don't have a city close by then you'll be surprised what the department store has available in catalog
This isn't ebay buddy, go to a tire shop in your area it will be way cheaperAnyone Got Yamaha ATV Tires?
IF you are rural and don't have a city close by then you'll be surprised what the department store has available in catalog
Is there anyone that has had a problem with the Yamaha ATV Rhino concerning Roll Overs?
I have an 04 Rhino with 26 inch tall 589 Mud tires and Black Rhino Performance CDI. Even with the taller tires I have not (yet) rolled it over. I take it on daily trips which entails VERY steep hillclimbs. As long as you adhere to common sense ATV rules (like only go straight up or straight down a hill) you will have no problems. With the BRP CDI my top speed is around 50 mph. I also highly recommend slowing down before making any sharp turns with this modification. I do know of someone from my area that let their inexperienced daughter ride one. She went up a hill at a side angle and rolled it. Her Left leg got flung outside the roll cage and it broke her leg.Is there anyone that has had a problem with the Yamaha ATV Rhino concerning Roll Overs?
Yamaha rhinos are very stable from the factory and can be highly modified, however if you add performance parts to it i highly recommend wider a-arms and lowering the body to reduce the risk of a rollover, and like someone else said, go straight up or straight down a hill.
Yamaha rhinos are very stable from the factory and can be highly modified, however if you add performance parts to it i highly recommend wider a-arms and lowering the body to reduce the risk of a rollover, and like someone else said, go straight up or straight down a hill.
My friend bought a 2001 Yamaha Blaster ATV Quad. It didn't come with a manual. Do I have to mix the oil & gas
My friend bought a 2001 Yamaha Blaster ATV Quad. It didn't come with a manual. It's a 2 stroke. Do I have to mix the oil %26amp; gas or does it do it automatically?My friend bought a 2001 Yamaha Blaster ATV Quad. It didn't come with a manual. Do I have to mix the oil %26amp; gas
There should be a tank at the back of the quad. Under the left rear fender. You feel that with oil and then feel the tank with normal gasoline and it mixes itself. It's called oil injection. If it is not there you need to mix the gas. I believe it's 32/1. To be sure go down to your local motorcycle shop and ask them.
There should be a tank at the back of the quad. Under the left rear fender. You feel that with oil and then feel the tank with normal gasoline and it mixes itself. It's called oil injection. If it is not there you need to mix the gas. I believe it's 32/1. To be sure go down to your local motorcycle shop and ask them.
Does anyone know the exhaust intake specs for a 1999 yamaha timberwolf atv?
you need to go to the closest yamaha dealer im sure they can identify it ..... another option would to go to www.yamaha.com and put your vin # there
I need help with my yamaha breeze ATV.?
i have a yamaha breeze ATV and it will not start it just keeps turning over but will not start what could be the problem?I need help with my yamaha breeze ATV.?
my answer is try to check it out first on auto repair shop...dudemiata
my answer is try to check it out first on auto repair shop...dude
Can a Polaris Glacier ATV plow system be mounted on a Yamaha Bruin 350?
Is there a mount kit available to fit the bruin?Can a Polaris Glacier ATV plow system be mounted on a Yamaha Bruin 350?
Yes i believe so. Check google/ebay.
Yes i believe so. Check google/ebay.
What atv company is better to buy Honda or Yamaha?
im looking for a atv and i want my atv to be safe, fast(but not to fast),i need it to be a sport, it needs to have well maneuvering, it it needs to be new and affordable
if possible feel free to list some atvs of these companies that fits what im looking forWhat atv company is better to buy Honda or Yamaha?
i would go with honda. i have a 01 400ex and i havent had to do nothing to it. i had to replace one part the whole time i owned it. other than just regular maintenance. always started right up. no problems that i have had. the 400ex goes around 70mph i think. which i dont know if u want that much power but its pretty powerfull. i would go with a 250 or 300 probly if u want a sport. thos go pretty fast i dont know how fast tho. probly 50mph im guessing.
if possible feel free to list some atvs of these companies that fits what im looking forWhat atv company is better to buy Honda or Yamaha?
i would go with honda. i have a 01 400ex and i havent had to do nothing to it. i had to replace one part the whole time i owned it. other than just regular maintenance. always started right up. no problems that i have had. the 400ex goes around 70mph i think. which i dont know if u want that much power but its pretty powerfull. i would go with a 250 or 300 probly if u want a sport. thos go pretty fast i dont know how fast tho. probly 50mph im guessing.
I have a yamaha atv and dont know what it is!?!?
I have the engine number 2vy-007878 but I don't know what size it is, or the model. Please help.I have a yamaha atv and dont know what it is!?!?
Sure you do, you told us. It's a Yamaha ATV
Sure you do, you told us. It's a Yamaha ATV
Which is a better atv? (yamaha grizzly 660 or Kawasaki brute force 650)?
and why. Plz, need advice, trying to buy a quad and need to know which has better performance and durability. Im going to be using it to do some nice muddin and to go on trails.Which is a better atv? (yamaha grizzly 660 or Kawasaki brute force 650)?
Yamaha Big Bear 4x4 is better cause its gear drive, not a cheap fan belt that drives a sheet metal clutch
If it was me go for the Grizzly, they are a lot better, my cousin has one, and won't give it up for the world. The Grizzly are also better in performaance and durability, it has a smoother rider and fun. You can go through a lot of mud with those.Which is a better atv? (yamaha grizzly 660 or Kawasaki brute force 650)?
I would go with the grizzly.
Why is Honda out of the question? If your looking for duarability and reliablity Honda is the way to go.
But anyway out of the yamaha and kawazaki you should go with the yamaha.
I have heard that the Brute Force has more power, but I have always liked the Grizzles.Which is a better atv? (yamaha grizzly 660 or Kawasaki brute force 650)?
YAMAHA 1000%
Yamaha Big Bear 4x4 is better cause its gear drive, not a cheap fan belt that drives a sheet metal clutch
If it was me go for the Grizzly, they are a lot better, my cousin has one, and won't give it up for the world. The Grizzly are also better in performaance and durability, it has a smoother rider and fun. You can go through a lot of mud with those.Which is a better atv? (yamaha grizzly 660 or Kawasaki brute force 650)?
I would go with the grizzly.
Why is Honda out of the question? If your looking for duarability and reliablity Honda is the way to go.
But anyway out of the yamaha and kawazaki you should go with the yamaha.
I have heard that the Brute Force has more power, but I have always liked the Grizzles.Which is a better atv? (yamaha grizzly 660 or Kawasaki brute force 650)?
YAMAHA 1000%
1995 yamaha warrior atv wont shift threw the gears when warm?
i got a 95 warrior atv and when the motor is cool it shifts and drives perfect but when it warms up it dont want to shift i still have gears but onl 2nd and 3rd theres enough oil in it and everything and the clutch is like new someone help please?1995 yamaha warrior atv wont shift threw the gears when warm?
Looks like its a warm up problem, just check all the worm gears, any one of them has a crack, which helps in shifting , because it expands after the engine is running for some time.Your clutch is fine. Another possibility could be your gear rods freeplay. Check whether freeplay increases when it heats up.mini countryman
Looks like its a warm up problem, just check all the worm gears, any one of them has a crack, which helps in shifting , because it expands after the engine is running for some time.Your clutch is fine. Another possibility could be your gear rods freeplay. Check whether freeplay increases when it heats up.
Having trouble with my 2002 Yamaha Grizzly ATV. Runs great the first few minutes and then it runs rough or die
my 2002 Yamaha Grizzly ATV. Runs great the first few minutes and then it runs rough or dies. It has done this since it got stuck in a snow drift last winter. It acts like it doesn't get enough fuel. Anything I can check?Having trouble with my 2002 Yamaha Grizzly ATV. Runs great the first few minutes and then it runs rough or die
Is the choke stuck?
Check any fuel filter, choke and your air filter, might be dirty or clogged, also check the spark plug, might be fouled.Having trouble with my 2002 Yamaha Grizzly ATV. Runs great the first few minutes and then it runs rough or die
Could be summer blend of gasoline.
Fuel Filter. Or sounds to me like you still have water in the carb..that can last for over a year or so...that would be my best guessHaving trouble with my 2002 Yamaha Grizzly ATV. Runs great the first few minutes and then it runs rough or die
Check for rust and water in your carburetor.
George
Start with the basics, if you haven't done it yet, change the oil, clean the filter, install a new spark plug.
Then see how it runs, if it's still doing the same thing, then as soon as it starts to run bad, stop and pull the spark plug. Does it smell like fuel? No fuel smell? Make sure the petcock and float bowl needle are clean and allowing fuel though.
If the plug smells like fuel, then put the cap back on the plug and ground it to the engine. Crank it over and check for spark. You should see a decently bright blue spark. If there's no spark, or it's weak, it may be an electrical problem.
Usually a bike that runs okay when it's cold, then runs like crud after it warms up has a bad CDI - but you can't really test them, and it's not cheap to replace, so start simple then work to the electrical problems.
If you've got another Grizzly (a friends bike, etc.), you can try trading out the CDI from his bike and see if the problem goes away. It won't hurt his CDI.
Is the choke stuck?
Check any fuel filter, choke and your air filter, might be dirty or clogged, also check the spark plug, might be fouled.Having trouble with my 2002 Yamaha Grizzly ATV. Runs great the first few minutes and then it runs rough or die
Could be summer blend of gasoline.
Fuel Filter. Or sounds to me like you still have water in the carb..that can last for over a year or so...that would be my best guessHaving trouble with my 2002 Yamaha Grizzly ATV. Runs great the first few minutes and then it runs rough or die
Check for rust and water in your carburetor.
George
Start with the basics, if you haven't done it yet, change the oil, clean the filter, install a new spark plug.
Then see how it runs, if it's still doing the same thing, then as soon as it starts to run bad, stop and pull the spark plug. Does it smell like fuel? No fuel smell? Make sure the petcock and float bowl needle are clean and allowing fuel though.
If the plug smells like fuel, then put the cap back on the plug and ground it to the engine. Crank it over and check for spark. You should see a decently bright blue spark. If there's no spark, or it's weak, it may be an electrical problem.
Usually a bike that runs okay when it's cold, then runs like crud after it warms up has a bad CDI - but you can't really test them, and it's not cheap to replace, so start simple then work to the electrical problems.
If you've got another Grizzly (a friends bike, etc.), you can try trading out the CDI from his bike and see if the problem goes away. It won't hurt his CDI.
Is a yamaha Banshee the same as a other Atv?
I just wanted to know is a banshee the same as a other Atv when you change gears, I know a banshee is a two stroke , can I get advice pls.Is a yamaha Banshee the same as a other Atv?
If you are asking about shifting only, the Banshee is like many motorcycles and most ATV's that have a hand clutch. It should be a 6 spd transmission. First gear is down from neutral, and the rest are up.
Lots of ATV's have automatic clutches (no hand clutch). And some are fully automatic. But most sport ATV's will be like the Banshee.Is a yamaha Banshee the same as a other Atv?
The banshee shifts the same as other ATV's. The thing I don't like about them is there is 2 of everything. 2 carbs, 2 pistons, 2 pipes etc, so if you rebuild it, it costs twice as much, and doesn't last twice as long.Is a yamaha Banshee the same as a other Atv?
Covenant Banshees are pretty nice.
The only differance from other sports atvs is that the banshee is two stroke. But the banshee is a badas* dune atv. I don't recommend it to a noob that's not on sand.
If you are asking about shifting only, the Banshee is like many motorcycles and most ATV's that have a hand clutch. It should be a 6 spd transmission. First gear is down from neutral, and the rest are up.
Lots of ATV's have automatic clutches (no hand clutch). And some are fully automatic. But most sport ATV's will be like the Banshee.Is a yamaha Banshee the same as a other Atv?
The banshee shifts the same as other ATV's. The thing I don't like about them is there is 2 of everything. 2 carbs, 2 pistons, 2 pipes etc, so if you rebuild it, it costs twice as much, and doesn't last twice as long.Is a yamaha Banshee the same as a other Atv?
Covenant Banshees are pretty nice.
The only differance from other sports atvs is that the banshee is two stroke. But the banshee is a badas* dune atv. I don't recommend it to a noob that's not on sand.
How do I find out the make and model on a used ATV with no VIN number?
I bought a used Yamaha ATV. There is no VIN number. How do I find out what year and model it is?
I only found numbers on the engine. ThanksHow do I find out the make and model on a used ATV with no VIN number?
There are at least two numbers on motorcycles and ATV's. One on the engine and one on the frame. I have several Yamaha ATV'S and the number on the frame is on one of the tubes that is towards the bottom where the engine is. Unless the frame has been power coated or modified, it should be there.
It should also be on your title or paperwork if you have them.
I only found numbers on the engine. ThanksHow do I find out the make and model on a used ATV with no VIN number?
There are at least two numbers on motorcycles and ATV's. One on the engine and one on the frame. I have several Yamaha ATV'S and the number on the frame is on one of the tubes that is towards the bottom where the engine is. Unless the frame has been power coated or modified, it should be there.
It should also be on your title or paperwork if you have them.
Location of serial number for Yamaha 1998 ATV Big Bear 4x4?
look underneath the rear left wheel well. You'll probably have to clean it real good first though
good luck
any problems, contact the Yamaha support line at 800-962-7926
good luck
any problems, contact the Yamaha support line at 800-962-7926
Where can I find a 12 volt battery for kids Yamaha raptor ATV?
Diecast ATV with Working Suspension, 4-pc Set:
Includes 4 assorted style ATVs: Suzuki, Yamaha, Kawasaki, and Honda
Real working suspension
Made of diecast metal and plastic, Ages 3+
Model Scale: 1:12
Each ATV come individually boxed
http://www.amazon.com/Diecast-ATV-Workin鈥?/a>
-*************Where can I find a 12 volt battery for kids Yamaha raptor ATV?
Hardware stores should have them.
Sometimes these batteries are used for electric lanterns.
You could try some place that sells sporting goods, or camping supplies.Where can I find a 12 volt battery for kids Yamaha raptor ATV?
wal mart
tractor supply
auto storeswalkie talkie
Includes 4 assorted style ATVs: Suzuki, Yamaha, Kawasaki, and Honda
Real working suspension
Made of diecast metal and plastic, Ages 3+
Model Scale: 1:12
Each ATV come individually boxed
http://www.amazon.com/Diecast-ATV-Workin鈥?/a>
-*************Where can I find a 12 volt battery for kids Yamaha raptor ATV?
Hardware stores should have them.
Sometimes these batteries are used for electric lanterns.
You could try some place that sells sporting goods, or camping supplies.Where can I find a 12 volt battery for kids Yamaha raptor ATV?
wal mart
tractor supply
auto stores
What is the 0-60 time on a stock 2005 Yamaha raptor 700 atv and a stock 2005 Yamaha YFZ450 atv?
That would depend totally on the types of surfaces you are riding on. ATV's are designed for offroad use, so how fast you get to 60 woudl depend on a million different things. Having said this, either of the ATV's you mentioned are probably the fastest ATV's around. They will scare the S*** out anyone but the most experienced riders.
What are he basic things i have to do after buying a brand new yamaha atv.?
so i just got brand new 09 yamaha 350 special edition(beast). Well im a little worrieed cause the guy at the dealership said that in about a month yamaha will call with some basic maintence questions. And if I answer incorectley i can get my atv taken away. Is this even true? and if it is what do they ask?. also can you give me some basic mainence tips and other overal tips for keeping this beast in the best condition. TnxWhat are he basic things i have to do after buying a brand new yamaha atv.?
There is a misunderstanding somewhere. You paid for the unit so it is now yours. Only way to lose it is if you financed it and failed to make payments. Might get a visit from the repo person. If it was to get stolen and you have no insurance. If you have lots of money and no job, and become a person of suspicion (like a drug dealer) it could be seized as part of a money laundering charge. I'm sure there are some other possibilities I missed. The simple fact that people would think twice before buying a Yamaha if this happened to even one customer, and Yamaha is in the business of selling.
The only thing that comes to mind is Yamaha might void your warranty. That is highly unlikely, and I have never heard of this happening for answering a maintenance question wrong.
What looks like should happen is your dealer receive low marks on their CSI score. Customer Satisfaction Index, which measures how each dealer satisfies their customers needs. You will get and email or letter in the mail, welcoming you to the Yamaha family, thanking you for your purchase. Then a multiple choice questionaire asking how you were treated, was the dealership clean, were the employees friendly, etc. When you get to the question "Did your salesperson go over your paperwork, owners manual, operation of vehicle"? you give them a "0". Unless you were so happy about getting your new ATV you ignored them or paid no attention. At some point they also should have taken you to the service department and introduced you to the service writers. This is where a good writer will try and schedule your first service.
Did you buy a Pre Paid Maintenance package (PPM)? Look on your paperwork if you do not know. If you did buy PPM, you only need to know the period (mileage, hours, months) when you should bring it in and have the factory service done by the selling dealer.
If you didn't buy PPM, then open up your owners manual and look in index for maintenance schedule. You will see when Yamaha recommends you need to clean your air filter, check or change oil %26amp; filter, inspect brakes, etc. The following pages expalin how to do all that is necessay with some nice pictures too. If your going to do this yourself or have a mechanic friend do it, I recommend you fill out in the back of the manual the area for documenting the services. Save your reciepts and keep it all together in one spot. If for some reason you have a failure and you want it covered by warranty, there could be a chance of denial if you cant prove the maintenace was performed. Lets say your just outside your warranty period and something happens. Yamaha would be more likely to cover it under "Goodwill" if you showed them maintenance was done to their recommendations.
I currently work at a motorcycle dealership, and years ago when I first started, it was in the service department as a service writer.
So go out and enjoy your new ATV, and always wear the right protective gear. Please.
Here is a good source for cheap parts and accessories:
http://stores.ebay.com/Cycle-Barn-Outlet鈥?/a>
wtf, that dealership is bunch of bull , what a bunch of idiots. they cannot do that. If they ever did it would be illegal. it's not trueWhat are he basic things i have to do after buying a brand new yamaha atv.?
You have no concerns, The Dealer Has no rite to take the machine back this is a bunch of BULL, however Maintenance is very Important, I would invest in a Repair Manual, It will be full or very Important Info, including any and All maintenance Schedules and recommended Fluid levels,
Grats on your Purchase and Be Safe, Got Helmet?
they dont care as long as they are making money on it.What are he basic things i have to do after buying a brand new yamaha atv.?
They can't take it away if you paid for it. If they do call all that they will ask is how you like the bike and how you were treated at your dealership. But, nonetheless, maintenance is still very important. Change the oil, look over everything before you go riding and make sure that everything looks good. Also, wear a helmet. I'm sure that you already have one, but I just like to remind people.
There is a misunderstanding somewhere. You paid for the unit so it is now yours. Only way to lose it is if you financed it and failed to make payments. Might get a visit from the repo person. If it was to get stolen and you have no insurance. If you have lots of money and no job, and become a person of suspicion (like a drug dealer) it could be seized as part of a money laundering charge. I'm sure there are some other possibilities I missed. The simple fact that people would think twice before buying a Yamaha if this happened to even one customer, and Yamaha is in the business of selling.
The only thing that comes to mind is Yamaha might void your warranty. That is highly unlikely, and I have never heard of this happening for answering a maintenance question wrong.
What looks like should happen is your dealer receive low marks on their CSI score. Customer Satisfaction Index, which measures how each dealer satisfies their customers needs. You will get and email or letter in the mail, welcoming you to the Yamaha family, thanking you for your purchase. Then a multiple choice questionaire asking how you were treated, was the dealership clean, were the employees friendly, etc. When you get to the question "Did your salesperson go over your paperwork, owners manual, operation of vehicle"? you give them a "0". Unless you were so happy about getting your new ATV you ignored them or paid no attention. At some point they also should have taken you to the service department and introduced you to the service writers. This is where a good writer will try and schedule your first service.
Did you buy a Pre Paid Maintenance package (PPM)? Look on your paperwork if you do not know. If you did buy PPM, you only need to know the period (mileage, hours, months) when you should bring it in and have the factory service done by the selling dealer.
If you didn't buy PPM, then open up your owners manual and look in index for maintenance schedule. You will see when Yamaha recommends you need to clean your air filter, check or change oil %26amp; filter, inspect brakes, etc. The following pages expalin how to do all that is necessay with some nice pictures too. If your going to do this yourself or have a mechanic friend do it, I recommend you fill out in the back of the manual the area for documenting the services. Save your reciepts and keep it all together in one spot. If for some reason you have a failure and you want it covered by warranty, there could be a chance of denial if you cant prove the maintenace was performed. Lets say your just outside your warranty period and something happens. Yamaha would be more likely to cover it under "Goodwill" if you showed them maintenance was done to their recommendations.
I currently work at a motorcycle dealership, and years ago when I first started, it was in the service department as a service writer.
So go out and enjoy your new ATV, and always wear the right protective gear. Please.
Here is a good source for cheap parts and accessories:
http://stores.ebay.com/Cycle-Barn-Outlet鈥?/a>
wtf, that dealership is bunch of bull , what a bunch of idiots. they cannot do that. If they ever did it would be illegal. it's not trueWhat are he basic things i have to do after buying a brand new yamaha atv.?
You have no concerns, The Dealer Has no rite to take the machine back this is a bunch of BULL, however Maintenance is very Important, I would invest in a Repair Manual, It will be full or very Important Info, including any and All maintenance Schedules and recommended Fluid levels,
Grats on your Purchase and Be Safe, Got Helmet?
they dont care as long as they are making money on it.What are he basic things i have to do after buying a brand new yamaha atv.?
They can't take it away if you paid for it. If they do call all that they will ask is how you like the bike and how you were treated at your dealership. But, nonetheless, maintenance is still very important. Change the oil, look over everything before you go riding and make sure that everything looks good. Also, wear a helmet. I'm sure that you already have one, but I just like to remind people.
I have a yamaha 80cc atv with extended cranking.(very long)?
I have a yamaha 80cc atv with extended cranking. I checked spark, fuel, and timing. Did not check compression. I think it's an 1980 something yamaha breeze. Any info. will be greatly appreciated.I have a yamaha 80cc atv with extended cranking.(very long)?
jets are plugged, pull the carb and clean the jets/float bowl, re adjust float, reassemble should run like a champ
jets are plugged, pull the carb and clean the jets/float bowl, re adjust float, reassemble should run like a champ
Can I remove a junk engine from my moped and put a yamaha atv engine instead?
So I have a SunL chinese moped that is pure junk and is always breaking down. It has a CVT transmission. I'm thinking of removing the junk engine and putting a Yamaha Blaster ATV engine in the frame of it to hopefully make it more reliable. Do you think this will work? I dont know since it's gonna be a new manual transmission with a chain. Instead of CVT. I will be working with someone is quite knowledgeable with engines. I have all the welding tools and other tools necessary to do this? What do you think?Can I remove a junk engine from my moped and put a yamaha atv engine instead?
I think it will work. The blaster is a 200 and not very heavy. The fact that it is air cooled makes it an easier project. I believe your engine (stock) hangs off the frame like an old Honda trail 90. If that is the case, you should be able to install the 200 no problem. Make it a chain drive and you will have a 5 speed moped. Sounds like fun to me.
I don't know why people have to be so negative about creating a fun project!
Good Luck
Respectfully, you will encounter problems galore it you tackle this project. Even if you shoe horn the engine into the frame, all the other components of the moped will not handle the extra weight and power.
While you are one of the few people that state they have access to fabrication tools, don't know if you have the necessary skills.
If you look at this as a learning exercise, then by all means, make it happen. If successful, you will have gained valuable experience and skills. Then you can move onto a new project.
Good LuckCan I remove a junk engine from my moped and put a yamaha atv engine instead?
Interesting project idea- legal issues possible-- 'Moped's usually under 50cc, a larger engine means 'motorcycle' license plate. Save your 'moped' registration and upgrade to 'motorcycle' at DMV when done, registration by frame number might mean no inspection for 'simple' (to DMV) engine replacement. As long as you have welder, cutting torch, drill and money you can do a lot of otherwise strange projects. Think of the guy who first put a Vincent engine in a Norton frame and what people may have said.
How is it going to fit in the cavity of the original engine?Can I remove a junk engine from my moped and put a yamaha atv engine instead?
sounds like an awesome transplant
you bought junk and no it wont work
I think it will work. The blaster is a 200 and not very heavy. The fact that it is air cooled makes it an easier project. I believe your engine (stock) hangs off the frame like an old Honda trail 90. If that is the case, you should be able to install the 200 no problem. Make it a chain drive and you will have a 5 speed moped. Sounds like fun to me.
I don't know why people have to be so negative about creating a fun project!
Good Luck
Respectfully, you will encounter problems galore it you tackle this project. Even if you shoe horn the engine into the frame, all the other components of the moped will not handle the extra weight and power.
While you are one of the few people that state they have access to fabrication tools, don't know if you have the necessary skills.
If you look at this as a learning exercise, then by all means, make it happen. If successful, you will have gained valuable experience and skills. Then you can move onto a new project.
Good LuckCan I remove a junk engine from my moped and put a yamaha atv engine instead?
Interesting project idea- legal issues possible-- 'Moped's usually under 50cc, a larger engine means 'motorcycle' license plate. Save your 'moped' registration and upgrade to 'motorcycle' at DMV when done, registration by frame number might mean no inspection for 'simple' (to DMV) engine replacement. As long as you have welder, cutting torch, drill and money you can do a lot of otherwise strange projects. Think of the guy who first put a Vincent engine in a Norton frame and what people may have said.
How is it going to fit in the cavity of the original engine?Can I remove a junk engine from my moped and put a yamaha atv engine instead?
sounds like an awesome transplant
you bought junk and no it wont work
I need help finding info on a 1980's Yamaha ATV quad with reverse any help?
So I am trying to get my wifes old Yamaha Quad running and having a lot of trouble the big problem is I don't know exactly what type of quad it is to look up parts. she bought it around 90 to 91 and said it was used when she got it. On one of the fenders it says something about now having auto reverse or something like that the fender is now under a mountain of snow so can't find out exactly what is says and no the name is not on it I checked before pulling the ATV in the garage. I pulled a serial number of the engine and it reads 52 H - 027259 like I said it's got to be mid to late 80's it has an electric start which doesn't currently work and a pull start if that helps it acts like it wants to run it has spark and gas is getting to it when I pull the crank it it seems to be firing just not starting and I think knowing exactly what type of quad it is will help thanks in advance if you can helpI need help finding info on a 1980's Yamaha ATV quad with reverse any help?
take a pic of it and send me a message with the pic. i will know what it is right away. the frame numbers would help too. to me it sounds like a big bear 350cc 4x4 or a warrior 350cc but get a pic of it and send it to me.I need help finding info on a 1980's Yamaha ATV quad with reverse any help?
A lot of time they will mount a plate on the bike someplace like on the steering shaft that will have the serial number and model number. Check the bike over closely and you should be able to find it. There is nothing on it to lead you to any brand at all? Markings decals or anything like that?mopar
take a pic of it and send me a message with the pic. i will know what it is right away. the frame numbers would help too. to me it sounds like a big bear 350cc 4x4 or a warrior 350cc but get a pic of it and send it to me.I need help finding info on a 1980's Yamaha ATV quad with reverse any help?
A lot of time they will mount a plate on the bike someplace like on the steering shaft that will have the serial number and model number. Check the bike over closely and you should be able to find it. There is nothing on it to lead you to any brand at all? Markings decals or anything like that?
Is the Yamaha Wolverine 450 4x4 a good ATV?
can somebdy comment ? the problem is that i just got a Yamaha Wolverine 450 4x4 and i really dont know if it is a good one . Can somebody help me ?Is the Yamaha Wolverine 450 4x4 a good ATV?
I would give it a 4 out of 5
I would give it a 4 out of 5
How to change carburetor jets in a 1998 yamaha warrior atv?
Remove and replace #15 [in link below] with desired size.How to change carburetor jets in a 1998 yamaha warrior atv?
remove carb from atv flip the carb upside down remove the 4 bolts holding the float bowl on remove the float bowl the main jet is in the middle its the bigger one the pilot jet is Right around the main a little below the main a small flat head screwdriver is required to remove the jets reassemble in revers order
remove carb from atv flip the carb upside down remove the 4 bolts holding the float bowl on remove the float bowl the main jet is in the middle its the bigger one the pilot jet is Right around the main a little below the main a small flat head screwdriver is required to remove the jets reassemble in revers order
How to take my 4 snow tires off my atv rim yamaha blaster?
i have a yamaha blaster 2003 with new 4 snow tires on it i have a set to go on but i cant get the 4 snow tire off the one peice rim with crow bars i dont want to damage the tire so is there a trick?How to take my 4 snow tires off my atv rim yamaha blaster?
Just take it to a tire shop it wont cost much like $7.00 a tire it is far easier so for 28.00 ur done and you can do it as fast as they can.
Just take it to a tire shop it wont cost much like $7.00 a tire it is far easier so for 28.00 ur done and you can do it as fast as they can.
Polaris or Yamaha ATV?
I am looking to buy a new ATV soon and I am torn on which model to get. I am stuck between the Yamaha Grizzly 450 or the Polaris Sportsman 400. The Polaris is $5699 new and the Yamaha is $6899 new so the Polaris has the edge on price. However I have heard mixed reviews on the suspension on the Polaris (mcpherson strut). I heard it can be like riding a pogo stick. The yamaha has independent A arms in front and back which is what I'm used to. Is it that noticeable or am I over thinking it? Any help would be great.Polaris or Yamaha ATV?
I say Polaris. Every Polaris ATV I he had lasted forever without having to get parts.Polaris or Yamaha ATV?
Polaris is better than Yamaha ATV. So i think you should buy Polaris.
I say Polaris. Every Polaris ATV I he had lasted forever without having to get parts.Polaris or Yamaha ATV?
Polaris is better than Yamaha ATV. So i think you should buy Polaris.
Yamaha ATV Mod and Tire Question?
I have a 2003 yamaha Bear Tracker 250 and i was wondering if there were any small performance mods (nothing huge or my dad will freak) for it to give it a little more "umpf" (i like to go fast) and also its in need of some new tires (front and rear) and i've looked every where and can't find some for less then around $65 a tire can any one help me out thanks.Yamaha ATV Mod and Tire Question?
I would start with a performance air filter, a UNI would be great. Then go on with a carburetor jet kit and an exhaust if you don't mind it being a little louder. These mods would wake it up quite a bit, I would go with a UNI air filter, Dynojet jet kit, and something like a Pro Circuit exhaust. For tires, keep your eyes open on eBay and ATV sites such as BikeBandit, Cheap Cycle Parts, and such.campers
I would start with a performance air filter, a UNI would be great. Then go on with a carburetor jet kit and an exhaust if you don't mind it being a little louder. These mods would wake it up quite a bit, I would go with a UNI air filter, Dynojet jet kit, and something like a Pro Circuit exhaust. For tires, keep your eyes open on eBay and ATV sites such as BikeBandit, Cheap Cycle Parts, and such.
Yamaha ATV Question on a 2001 Yamaha Wolverine 4x4?
I own a 2001 Yamaha Wolverine 4x4. I never had an issue with the 4x4 system and never really needed it or paid attention to it. The other night, I got stuck and needed it. I noticed that when trying to get unstuck, the back wheels and one front wheel (the right hand side) where spinning. The left hand side tire barely moved.
Is this normal? Is a 3 wheel drive? or is it supposed to be a true 4 wheel drive and I have a problem?
Hoe does the all time 4x4 system on this atv work? I am used to polaris and their AWD system. The tires take turns, etc.
ThanksYamaha ATV Question on a 2001 Yamaha Wolverine 4x4?
Yes it's normal.The rear axil is a fixed axil so both rear wheels turn together.the front axil has a set of spider gears in it making it a true differential.Without this your bike would not be able to turn without hopping all over the place.
Is this normal? Is a 3 wheel drive? or is it supposed to be a true 4 wheel drive and I have a problem?
Hoe does the all time 4x4 system on this atv work? I am used to polaris and their AWD system. The tires take turns, etc.
ThanksYamaha ATV Question on a 2001 Yamaha Wolverine 4x4?
Yes it's normal.The rear axil is a fixed axil so both rear wheels turn together.the front axil has a set of spider gears in it making it a true differential.Without this your bike would not be able to turn without hopping all over the place.
Sunday, January 8, 2012
Yamaha atv engine help?
Yamaha Badger YMF80-4 stroke, with auto clutch 4 speed. so since the battery went bad, it has no kick start so we would have it in neutral and push it, then shift into 1st and it would start. so the last time we did tryd that the atv stoped and the tires dont spin but if you put in in 4th grear you can roll the atv super slow, so what happend to the engine? i would like to take it apart and try to fix it, but it would help to know where the problem is before i start taking the engine apart.|||Can't begin to imagine how you can push-start something with an automatic clutch unless there's something wrong with the clutch i.e. it's not disengaging properly, so I would say start by pulling the clutch apart and servicing/repairing it. It is always harder to push a vehicle in gear in first than in top, so the symptoms you describe lead me to that conclusion.|||could be timing chain... broken or jumped a tooth???
What is the name of the new ATV maker that my Honda/Kawasaki/Yamaha dealer is carrying?
I recently saw this thing at the dealership and they said that it was a company that has made parts for Honda for 15 years, supposedly quite reputable. I have Googled, but can't find the name of it. Anyone?|||Is it Can_Am?|||yeah, Is it Can_Am?|||I don't know about their ATVs, but, I frequently read a few scooter forums, and the Kymco scooters are highly regarded and frequently recommended. They also are supposed to have a good warranty program ??? .
Where can an albertan get a yamaha ATV????
i live in alberta, about an hour north of edmonton. is there any place near me that i could buy a YFM 350R?
how much would it cost?|||Depends if you want brand new or used. If you would settle for a slighlty used, check out the Trader magazine or Trader online. They have tons of stuff near and around Edmonton and north. If not you'd probably have to check Edmonton for a Yamaha dealership.
(They could ship it to you, or close to you anyway, you'd have to inquire.)
For cost, check out the magazines and online for blackbook prices so you don't get ripped off!
how much would it cost?|||Depends if you want brand new or used. If you would settle for a slighlty used, check out the Trader magazine or Trader online. They have tons of stuff near and around Edmonton and north. If not you'd probably have to check Edmonton for a Yamaha dealership.
(They could ship it to you, or close to you anyway, you'd have to inquire.)
For cost, check out the magazines and online for blackbook prices so you don't get ripped off!
How much did a 2003 Yamaha warrior 350(atv) cost brand new back in 2003?
I was thinking of buying one. If you own one what do you think of it?|||i believe.....imo...they were just under 4000. my friend bought a brand new one for like 3700 after negotiating...hope this helps
I have a 2001 Yamaha Warrior 350 atv with starting problems?
It has electric start. Pulled plug and I only get some spark right after I stop pressing start button on handlebar. When pressed no spark. Only when released. Just rebuilt starter and all was working fine. New battery too. Only other thing I did was change oil and wash atv. Any advice as far as trouble shooting would be greatly appreciated|||check your starter solenoid and look at all the wiring to make sure nothing is grounding out or got wet while washing.|||I have a feeling that you've got something timed improperly in the starter mechanism, or the starter button has a weird ground or lack of ground that's causing the problem.
It would not be the CDI, unless this is an ongoing problem. Usually a CDI will show issues first when the engine is hot, but run fine when it is cold.
A coil would not be affected by the starter button position.|||its probably your CDI. im no expert but thats what i would think.
It would not be the CDI, unless this is an ongoing problem. Usually a CDI will show issues first when the engine is hot, but run fine when it is cold.
A coil would not be affected by the starter button position.|||its probably your CDI. im no expert but thats what i would think.
Yamaha ATV moto4 250?
Just got a yamaha atv and need some parts for it,but i dont have the year model. So i was wondering if anyone knows where the vin number would be so i could decode it?|||Your best place to check will be the nearest Yamaha MC Dealer.
But if you state at least the color of the quad I could give you a guess!
Added @ add - It's a '87 or later, thanks.|||Sorry its not crap Mate
|||Sorry but it's crap mate.
But if you state at least the color of the quad I could give you a guess!
Added @ add - It's a '87 or later, thanks.|||Sorry its not crap Mate
Report Abuse
|||Sorry but it's crap mate.
I have a 1986 80cc yamaha atv what makes the starter stay ingaged and burn up while running. what to do to fix
You could get a push button from an auto supply shop. Wire it between the hot wire of the starter. Your starter will only run when it's pushed at start up. Or take it to a repair shop and spend a lot of money to have it fixed.
03 yamaha blaster atv wont start?
it has compression,spark. but the kick start spring is broken|||More information needed.
Are there snap rings in my bearing carrier on my Yamaha Warrior 350 atv? Please answer!?
Im trying to change my bearings in my carrier. The axle will not slide out. Are there snap rings behind the seal preventing the axle from sliding out? Every thing is stock and its a Yamaha warrior 350 atv. Please answer Thanks|||Well the fact your still having problems means I didn't do what i should have on the first go round of seeing your question. You need a service manual, you can get one here online for cheap. It has pictures and everything. http://www.cyclepedia.com/yamaha-raptor-鈥?/a> This way you'll know you did it right and can fix problems later also.|||well if there is a snap ring it will be where you can see it and get it off so behind wouldnt be.. could be on inside of gear box maybe|||Worse than any Hidden Snap Ring .
There's a Spacer Tube on the Axle,,Between the Bearings,,,Inside the Case.
It has become Rusted to the Axle.
The axle is supposed to be a Slide Fit thru the bearings.
Axles and Bearings virtually NEVER freeze together.
But it also must Slide thru the Bearing Spacer,,,,which grows roots to the axle.
......................................鈥?br>
To get it OUT,,,,
obviously the Axle will not slide thru as intended.
You are going to have to either BEAT It out,,or PRESS it out.
There's very little chance you'll be able to break the bond between Axle %26amp; Spacer.
So Expect the Spacer to push the Bearing out of the case.
It comes OUT by hitting or Pressing on Sprocket Side of Axle,,,and out thru the R/H Brake Side.
The seal's press fit is Tight-ish.
Pry the R/H Brake Side Seal and Dust cover Out of the axle carrier case.
That reduces the Force required because Bearing must Come out ,,,while STUCK to the Axle,,,and it wont have to drive seal along with it.
Re-Install the Wheel Hub on the L/H end of the Axle,,Sprkt Side.
Only That hub,,nothing else.
Get a short piece of pipe that fits OVER the end of axle,,,
but Buttts- against the Nut/Washer Seat of the Hub.
Beat on that Pipe with a Big Hammer,,Sledge Hammer.
You can get a pipe at any hardware store for cheap.
1" or 1.5" Diameter a Foot long should do.
Also get a CAP for the pipe,,to have something to Hit on besides a Hole in the pipe.
Might wanna get a big Washer to between the Hub and Pipe for a "seat" so ya dont mess up the spline intersection @ Hub /Axle.
You shouldn't beat the hell outa it.
If it's REALLY tough,,,,get a LONG pipe to fit over the Other side of Axle and up against Bearing.
Buttt that against something SOLID,,,like a Tree,,,,or a bord on the ground,,,etc.
That "AxleCoverPipe" will take all the force,,,and not your axle carrier case,,rear susp.arms,mounting hardware,etc.
OR,,,take it to a autoparts store that presses on axle bearings,,,or a bike shop,,,,and have them Press the axle out.
You can rig up a press all sorts of ways,,,using a puller body,or a bottle jack----but I'll skip that.
"If I gotta Tell ya how,,,Ya got no bidness doing it"-----good way to get hurt BAD or damage something while Learing the Hard Way.
......................................鈥?br>
It MIGHT come out Easy,,
Or turn into a Prize Fight %26amp; be a full 15 round slugfest.
If it's gonna be Too Tuff,,,,take the Stripped Down axle assembly to a shop ,,to be Pressed out.
......................................鈥?br>
OLD,,,"re-claimed" spacers are better than NEW ones.
Because after getting them cleaned-up inside,,,,they are far less likely to seize-up again.
New ones are Cheap %26amp; Easier.
Coat the Axle and the Inside of the spacer with a Bunch of heavy grease is all ya need to do to keep it from happening again
......................................
Here's a Picture
http://images.powersportsnetwork.com/fic鈥?/a>
#19 Spacer is stuck to #11 Axle,,,
while Inside the #18 Case ,,,trapped Between the 2- #20 Bearings.
Beating/Pressing on Left End of axle makes Axle slide thru Left Side Brng like normal,,,
While the Stuck #19 Spacer drives the R/H #20 Bearing OUT of the Case,,
allowing axle to come Thru %26amp; OUT.
Soak the spacer in penetrating oil.
And Beat it all up%26amp;down it's length to break up the rust.
If you want to SOAK the spacer,,,
Get a long plastic bag,,
Push the axle THRU the Bottom,,,and slide bag over spacer.
Twist the bag Tight around axle and ducttape it,or wire-tie it tightly to seal upon axle.
Twist Bag around axle to reduce "Ballooning " so Less Oil is required to Fill the bag.
Fill the Bag ,,,stand axle on end%26gt;%26gt;check back later after soaking a while.
Real penetraing oil is Pricey @ enough quantity to fill the bag.
ATF mixed with Charcoal lighter fluid works Great.
Plain Diesel does also.
"Lamp Oil" ,,kerosine,,all that sorta stuff does work OK,,and is Cheap
Good Luck
......................................鈥?br>
I Forgot to mention,,,
Yamaha is the TYPO KING.
Looking at the Parts Drawing,,,which IS genuine Yamaha from a different source,,,
The Locknuts on the axle which tighten against the Sprocket Carrier are MISSING in the photo,,,LOL.
Any publication from Yamaha,,,,ALWAYS be Skeptical of the accuracy of both TEXT and Illustrations.
They screw-up more than probaly everybody else put together
Here's an '87 Parts Diagram.
Note the 2- #25 SprocketCarrier Retainer Nuts.
http://images.powersportsnetwork.com/fic鈥?/a>
Originally ,,Yamaha use Spanner-Drive RING NUTS.
They had back-off probs with 'em.
So they Superceded the part and now use Regular HEX NUTS.
When they made the Change,,,they DELETED the Old Ring Nuts from the Engineering Drawing,,
but failed to pencil-in their Replacement,,the new HEX nuts.
So instead of displaying the WRONG Nuts,,,,it doesn't show ANY nuts at all in that position.
In some situations,,that could be Not as comical as it sounds for anyone trying to fit their bike %26amp; not knowing what all goes where.
DO INDEED put the Nuts there,,,Yours should already have the New Hex ones.
And once more,,just for sake of repeating%26gt;%26gt;%26gt;
Axle MUST go OUT in Correct Direction,,,ONLY goes thru ONE Way.
The RIGHT Direction is OUT the RIGHT Side.
Right direction to go back IN is Thru the RIGHT Side.
There's a Spacer Tube on the Axle,,Between the Bearings,,,Inside the Case.
It has become Rusted to the Axle.
The axle is supposed to be a Slide Fit thru the bearings.
Axles and Bearings virtually NEVER freeze together.
But it also must Slide thru the Bearing Spacer,,,,which grows roots to the axle.
......................................鈥?br>
To get it OUT,,,,
obviously the Axle will not slide thru as intended.
You are going to have to either BEAT It out,,or PRESS it out.
There's very little chance you'll be able to break the bond between Axle %26amp; Spacer.
So Expect the Spacer to push the Bearing out of the case.
It comes OUT by hitting or Pressing on Sprocket Side of Axle,,,and out thru the R/H Brake Side.
The seal's press fit is Tight-ish.
Pry the R/H Brake Side Seal and Dust cover Out of the axle carrier case.
That reduces the Force required because Bearing must Come out ,,,while STUCK to the Axle,,,and it wont have to drive seal along with it.
Re-Install the Wheel Hub on the L/H end of the Axle,,Sprkt Side.
Only That hub,,nothing else.
Get a short piece of pipe that fits OVER the end of axle,,,
but Buttts- against the Nut/Washer Seat of the Hub.
Beat on that Pipe with a Big Hammer,,Sledge Hammer.
You can get a pipe at any hardware store for cheap.
1" or 1.5" Diameter a Foot long should do.
Also get a CAP for the pipe,,to have something to Hit on besides a Hole in the pipe.
Might wanna get a big Washer to between the Hub and Pipe for a "seat" so ya dont mess up the spline intersection @ Hub /Axle.
You shouldn't beat the hell outa it.
If it's REALLY tough,,,,get a LONG pipe to fit over the Other side of Axle and up against Bearing.
Buttt that against something SOLID,,,like a Tree,,,,or a bord on the ground,,,etc.
That "AxleCoverPipe" will take all the force,,,and not your axle carrier case,,rear susp.arms,mounting hardware,etc.
OR,,,take it to a autoparts store that presses on axle bearings,,,or a bike shop,,,,and have them Press the axle out.
You can rig up a press all sorts of ways,,,using a puller body,or a bottle jack----but I'll skip that.
"If I gotta Tell ya how,,,Ya got no bidness doing it"-----good way to get hurt BAD or damage something while Learing the Hard Way.
......................................鈥?br>
It MIGHT come out Easy,,
Or turn into a Prize Fight %26amp; be a full 15 round slugfest.
If it's gonna be Too Tuff,,,,take the Stripped Down axle assembly to a shop ,,to be Pressed out.
......................................鈥?br>
OLD,,,"re-claimed" spacers are better than NEW ones.
Because after getting them cleaned-up inside,,,,they are far less likely to seize-up again.
New ones are Cheap %26amp; Easier.
Coat the Axle and the Inside of the spacer with a Bunch of heavy grease is all ya need to do to keep it from happening again
......................................
Here's a Picture
http://images.powersportsnetwork.com/fic鈥?/a>
#19 Spacer is stuck to #11 Axle,,,
while Inside the #18 Case ,,,trapped Between the 2- #20 Bearings.
Beating/Pressing on Left End of axle makes Axle slide thru Left Side Brng like normal,,,
While the Stuck #19 Spacer drives the R/H #20 Bearing OUT of the Case,,
allowing axle to come Thru %26amp; OUT.
Soak the spacer in penetrating oil.
And Beat it all up%26amp;down it's length to break up the rust.
If you want to SOAK the spacer,,,
Get a long plastic bag,,
Push the axle THRU the Bottom,,,and slide bag over spacer.
Twist the bag Tight around axle and ducttape it,or wire-tie it tightly to seal upon axle.
Twist Bag around axle to reduce "Ballooning " so Less Oil is required to Fill the bag.
Fill the Bag ,,,stand axle on end%26gt;%26gt;check back later after soaking a while.
Real penetraing oil is Pricey @ enough quantity to fill the bag.
ATF mixed with Charcoal lighter fluid works Great.
Plain Diesel does also.
"Lamp Oil" ,,kerosine,,all that sorta stuff does work OK,,and is Cheap
Good Luck
......................................鈥?br>
I Forgot to mention,,,
Yamaha is the TYPO KING.
Looking at the Parts Drawing,,,which IS genuine Yamaha from a different source,,,
The Locknuts on the axle which tighten against the Sprocket Carrier are MISSING in the photo,,,LOL.
Any publication from Yamaha,,,,ALWAYS be Skeptical of the accuracy of both TEXT and Illustrations.
They screw-up more than probaly everybody else put together
Here's an '87 Parts Diagram.
Note the 2- #25 SprocketCarrier Retainer Nuts.
http://images.powersportsnetwork.com/fic鈥?/a>
Originally ,,Yamaha use Spanner-Drive RING NUTS.
They had back-off probs with 'em.
So they Superceded the part and now use Regular HEX NUTS.
When they made the Change,,,they DELETED the Old Ring Nuts from the Engineering Drawing,,
but failed to pencil-in their Replacement,,the new HEX nuts.
So instead of displaying the WRONG Nuts,,,,it doesn't show ANY nuts at all in that position.
In some situations,,that could be Not as comical as it sounds for anyone trying to fit their bike %26amp; not knowing what all goes where.
DO INDEED put the Nuts there,,,Yours should already have the New Hex ones.
And once more,,just for sake of repeating%26gt;%26gt;%26gt;
Axle MUST go OUT in Correct Direction,,,ONLY goes thru ONE Way.
The RIGHT Direction is OUT the RIGHT Side.
Right direction to go back IN is Thru the RIGHT Side.
Why cant these mini atv pickups like the Yamaha Rhinos and i think other companies have them too,?
be made to be street legal, for like in town or rural use, I dont think they be too great on the freeways. I am sure they get much better milage, or could be made to.|||They are street legal in a few states only, SD and AZ for sure, if proper lights installed.|||Not very safe. Its roll cage probably aint strong enough.|||They only go about 15 to 20 MPH|||Because its not safe. Also they go only about 50.|||Some might be legal in some states- Wisconsin and Iowa have a couple loopholes for some properly equipped. You didn't state what state you're in so make little difference pointing out Wisconsin 'Implement of husbandry' class of vehicles or 'Neighborhood commuter vehicle'- basically a moped licensed and restricted 3 or 4 wheel vehicle for towns. So- some states let the various vehicles on streets and country roads at various times, my sister can run her Yamaha ATV with it's weed sprayer, cargo basket and power take off equipped , lighted 4 wheeler and it is classed the same as small tractor. JD Gators get allowed on roads same way in Wisconsin sometimes. Yamaha golf carts with a rollbar and some other equipment get allowed on town streets under 25 mph limits in Arizona and Florida- license plate is same class as mopeds.
What are the valve settings for a 2000 Yamaha Warrior ATV?
Remove the rocker covers as said, but u'll need to remove the timing chain cover and crank cover also. Turn the crank nut till the timing mark on the cam sptocket lines up with the mark on the case. Use feeler guages.
Intake: .0023-.0039
Exhaust: .0063-.0078
this is done on a cold engine.|||Those are the correct settings.
In case you need it, the chain tension is 30-40mm (drive chain)|||If its the same as my Warrior, there are two caps at the top of the engine, one over the muffler, one over the entrance into the engine from the carbuerator. Take the bbolt out and remove the caps, there will be the roccker arm and at the end is a bolt lookin thing with a nut on the top, Tightn the bolt down so it barely makes a tapping noise when u push it up and down. Then ur all set.
Intake: .0023-.0039
Exhaust: .0063-.0078
this is done on a cold engine.|||Those are the correct settings.
In case you need it, the chain tension is 30-40mm (drive chain)|||If its the same as my Warrior, there are two caps at the top of the engine, one over the muffler, one over the entrance into the engine from the carbuerator. Take the bbolt out and remove the caps, there will be the roccker arm and at the end is a bolt lookin thing with a nut on the top, Tightn the bolt down so it barely makes a tapping noise when u push it up and down. Then ur all set.
I need help taking apart the rear end of my yamaha moto4 atv will someone help me.?
i dont want some pointless answer, i want details, step by step dismantling instructions, and diagrams, nothing else|||Go toi a bike shop and buy a CLYMER MANUAL. It has everything make sure you get one for your ATV
Best Yamaha ATV?
I was wondering what the best Yamaha ATV out there is. I would rather have a consumers opinion. Please give details for your choice.|||I'm not into ATV's, but my brother had a Yamaha Blaster. It was fast.|||duuuuuuude... a blaster? ha ha ... get a yamaha yzf 450. I race in the WORCS series.. the majority of quads out there are either Yamaha YZF 500's or Honda TRX450's and jsut recently the new suzuki R450 (fuel injected) has been kicking tail.
Report Abuse
What is a better ATV? Yamaha raptor 350 or Yamaha banshee
What is a better ATV? Yamaha raptor 350 or Yamaha banshee
I cant make up my mind on whether i should get a raptor 350 or a banshee. So what is a better atv?
|||banshee!.....
I cant make up my mind on whether i should get a raptor 350 or a banshee. So what is a better atv?
|||banshee!.....
Can you put a turbo on a yamaha warrior atv?
if so what kind of turbo would you put on ?|||you would have to design and make your own fitments and use a turbo that would suit the application,,done one once on a xt600 and got pics of a one off supercharged xt660 costing around 拢22'000 10 years ago......stick NOS on it ,done that as well..lots cheeper and just as much fun.....
Which is better for a atv,honda or yamaha?
I am looking to buy a used honda trx400ex and was wondering if honda is a good brand for atv, or is a yamaha yfz 450 the better choise thanks.|||The yfz has a lot of power,but Honda probably would be better,as far as being reliable,and having a motor that will last.|||Theyz both equal in power.
Why Are yamaha Bashee atv's so dam fast? And why are they faster the my raptor 660?
I can't figure out why they are so fast... Also I was in Glamis about to race this Guy on my raptor and i know that i have raptors have torque cuz i popped a willy right onto my ***. but why are banshee's faster?|||Engines are lighter in weight and produce more horse power. That is the advantage of two stroke engines.|||Different brands....but banashees are usually always more modified, raptors are fast but they take off fast but top speed is normal|||Nothing can beat a 2 stroke when it comes to acceleration. A stock KX65 is faster than a raptor 700
Where's the VIN number on a Yamaha ATV?
I have a 90' Yamaha Big Bear 350 and cant find the VIN # anywhere|||The VIN number is going to be in one of two places. Look on the left side of your vehicle's frame behind the front tire. If it is not there, you may want to check the lower frame rail beneath the engine.
Your VIN is a 17-digit number that contains information about your Big Bear as well as identifies it.
Your VIN is a 17-digit number that contains information about your Big Bear as well as identifies it.
What is the maintenance of a sport yamaha atv raptor?
what is a good atv to purchase|||i have a 660 raptor and a 700 raptor. The maintance I do is a little more than the dealer requires but I ride them pretty hard. I change the oil every 15 hours, I change the coolant every 4 or 5 times i go out. Check the spark plug, and the gear oil frequently. I love them raptors, have fun
How do I get my '99 yamaha blaster 200cc atv to idle?
The Blaster has an electronic device controlling the idle. Look at the carb, you will see a strange looking box on top of the normal carb, it is a solenoid which controls idle speed. In the throttle housing on the handle bar, is a switch, which activates the box. I am not sure how the bike determines when the idle speed is to be adjusted, but that control box can give trouble, causing the bike to shut down when the throttle is closed, and the switch in the throttle housing transfers. Also, the control box can cause the carb to idle very fast. I had a customer last October with this problem, I solved it for him. If you think this may be your
trouble, you may E-mail me for instructions as to how to repair it. I do not want to take up space/time on ANSWERS if this is not your problem.
Tomcotexas@yahoo.com|||If you think it has a clog take a hammer (I'm serious I did this to my Warrior) and tap the carb with it. Not to hard but not to soft either. Then adjust the screw once the engine is warmed up. Make sure you put some fresh gas in there.|||You need to clean the Carb. Specifically, the pilot jet.
If you dont know how to clean it you can get a Clymer or Haynes manual and read about how to do it. If it is not CLEAR to you what to do after that, have a local shop take care of it for you. It is very easy to miss the pilot jets when cleaning a carb.|||First thing i would suggest is check ur jetting. If that looks good clean the carb.|||before u take apart the carb adjust the idle screw and the air screw. they are very fussy, one cant be wrong or the machine wont run properly. then if that didnt work clean the carb and adjust the scews after. the reeds also may be causing the problem.
trouble, you may E-mail me for instructions as to how to repair it. I do not want to take up space/time on ANSWERS if this is not your problem.
Tomcotexas@yahoo.com|||If you think it has a clog take a hammer (I'm serious I did this to my Warrior) and tap the carb with it. Not to hard but not to soft either. Then adjust the screw once the engine is warmed up. Make sure you put some fresh gas in there.|||You need to clean the Carb. Specifically, the pilot jet.
If you dont know how to clean it you can get a Clymer or Haynes manual and read about how to do it. If it is not CLEAR to you what to do after that, have a local shop take care of it for you. It is very easy to miss the pilot jets when cleaning a carb.|||First thing i would suggest is check ur jetting. If that looks good clean the carb.|||before u take apart the carb adjust the idle screw and the air screw. they are very fussy, one cant be wrong or the machine wont run properly. then if that didnt work clean the carb and adjust the scews after. the reeds also may be causing the problem.
Yamaha 350cc ATV will not start. No spark! What to check?
This summary is not available. Please
click here to view the post.
Yamaha ATV Question?
I was wondering what the best Yamaha ATV out there is. I would rather have a consumers opinion. Please give details for your choice.|||Polaris Baby!!!!
Forget Yamahahahahaha|||Don't listen to the fella above, I have friends with Polaris ATV's, and while they perform good their reliability sucks.
Yamahas are very reliable ATV's from my experience. I've owned 3 and never had a problem with any of them (86' YFM 200 Moto 4, 96' Big bear, 04' Wolverine) and I ABUSED them all! If you want a no frills bulletproof ATV at a good price then i'd go with the Big Bear 400, the only drawback to most is they are not automatics (they're 5 speed foot shift semi auto's). They are indestructible. If auto is a must get a Grizzly 660 or 700 EFI, the Kodiak's (400 and 450) just don't have enough grunt for me, plus the Grizz comes with a locking front differential as standard equipment and ample ground clearance. If you want performance go with the Raptor 700R or the YFZ 450. The 700R isn't a quick as the YFZ but it has reverse and the YFZ does not. If you want something that's a true workhorse look at a Rhino 660 side x side, they're amazing and as fun to drive as an ATV, yet they seat two people and have a bed in the back!
Forget Yamahahahahaha|||Don't listen to the fella above, I have friends with Polaris ATV's, and while they perform good their reliability sucks.
Yamahas are very reliable ATV's from my experience. I've owned 3 and never had a problem with any of them (86' YFM 200 Moto 4, 96' Big bear, 04' Wolverine) and I ABUSED them all! If you want a no frills bulletproof ATV at a good price then i'd go with the Big Bear 400, the only drawback to most is they are not automatics (they're 5 speed foot shift semi auto's). They are indestructible. If auto is a must get a Grizzly 660 or 700 EFI, the Kodiak's (400 and 450) just don't have enough grunt for me, plus the Grizz comes with a locking front differential as standard equipment and ample ground clearance. If you want performance go with the Raptor 700R or the YFZ 450. The 700R isn't a quick as the YFZ but it has reverse and the YFZ does not. If you want something that's a true workhorse look at a Rhino 660 side x side, they're amazing and as fun to drive as an ATV, yet they seat two people and have a bed in the back!
Is there an extended swing arm kit for '04 yamaha 660r raptor atv?
I hate the way that my 660r wants to willie so easily, especially while going up hills. the torque is hard to control with the throttle and i would like to dampen the bikes tendency to want to willie, with its crappy high center of gravity. is there an extended swing arm kit that i can use? thanks.|||http://www.newircusers.com/store/rk2007_鈥?/a>
The site keeps changing the pictures of different items they sell.
I did see a Raptor extended swingarm - contact them.
This site will build to your specifications -
http://www.traxatv.com/shopcart/eyeball-鈥?/a>
If you don't mind spending money and like stability, consider an extended rear axle.
The wider stance will help prevent your quad from tipping over.
I don't know if it will hinder trail riding, being so wide.
The site keeps changing the pictures of different items they sell.
I did see a Raptor extended swingarm - contact them.
This site will build to your specifications -
http://www.traxatv.com/shopcart/eyeball-鈥?/a>
If you don't mind spending money and like stability, consider an extended rear axle.
The wider stance will help prevent your quad from tipping over.
I don't know if it will hinder trail riding, being so wide.
Can u adjust a yamaha bruin 250 atv to run straight pipe/performance exhaust?
I also need to know were i could get a exhaust for it....
It needs to make it loud, cuz im tired of riding with people with freakin 700cc atvs and think their so bad *** just because they heard a mile away.....
PLEASE HELP!!!!!!!!!!!!!!!|||A 250 atv will still be a 250 atv regardless of what exhaust is fitted, if you fit a straight pipe with no muffler it will actually loose performance. Fact is you are the 'underdog' in the pack so either accept it or waste a heap of money like your mates and go get a 700cc model. After all, it's all for fun isn't it and it sounds like your not having much with your present friends.
It needs to make it loud, cuz im tired of riding with people with freakin 700cc atvs and think their so bad *** just because they heard a mile away.....
PLEASE HELP!!!!!!!!!!!!!!!|||A 250 atv will still be a 250 atv regardless of what exhaust is fitted, if you fit a straight pipe with no muffler it will actually loose performance. Fact is you are the 'underdog' in the pack so either accept it or waste a heap of money like your mates and go get a 700cc model. After all, it's all for fun isn't it and it sounds like your not having much with your present friends.
What is the difference between the yamaha raptor 350 and yamaha warrior (ATV).?
It's essentially the same bike - has been for over two decades. Same bore and stroke, same compression ratio, both six speeds, the Raptor is a bit lighter and the Raptor has a bit more travel - yet a tiny bit less clearance. Same size tires and fuel capcity.
They made some minor changes when they renamed it the Raptor, but they share the same basic motor/drivetrain.
They Raptor has a different look due to the redesigned plastics.
If you are considering either, take a look at the new Raptor 250 - very quick and nimble.|||they read simular, however the warrior has a tremendious resale value, it seems more of the mud ape beast, where the raptor seems to be a little more speedy, doesnt have all reversing like the warrior but has a snorkel set up higher.
http://www.motorcycle.com/manufacturer/y鈥?/a>
http://www.yamaha-motor.com/sport/produc鈥?/a>|||everything is the same except for the frame, plastics, and drive sprockets. they both share the same engine but the raptor is geared for more speed.|||I find some articles for you here:
http://automotive.cnwaper.com/html/ATV/i鈥?/a>
They made some minor changes when they renamed it the Raptor, but they share the same basic motor/drivetrain.
They Raptor has a different look due to the redesigned plastics.
If you are considering either, take a look at the new Raptor 250 - very quick and nimble.|||they read simular, however the warrior has a tremendious resale value, it seems more of the mud ape beast, where the raptor seems to be a little more speedy, doesnt have all reversing like the warrior but has a snorkel set up higher.
http://www.motorcycle.com/manufacturer/y鈥?/a>
http://www.yamaha-motor.com/sport/produc鈥?/a>|||everything is the same except for the frame, plastics, and drive sprockets. they both share the same engine but the raptor is geared for more speed.|||I find some articles for you here:
http://automotive.cnwaper.com/html/ATV/i鈥?/a>
Looking to find some information on a yamaha atv motor rebuild?
just put back together need some advise on adjstments|||you might have better luck asking in the motorcycle section.
and be specific about what you want to know.
and be specific about what you want to know.
Atv yamaha is there a good paint out there for atv plastic ?
yes spray paint is really good and helpful
How much is a 05' yamaha warrior atv worth?
i have a yamaha warrior atv 05' and it has a aftermarket exhaust,k%26amp;n air filter,nerf bars and a extended rear axle?|||its only worth what someone will give you for it. and dont expect to get your money back for the bolt on parts that you have installed.|||just go to kbb.com and they will give you the right amount.
Can i put a plow on a Yamaha Wolverine 450 4X4 ATV?
I was planning on getting one, but i was wondering if it could handle a plow?|||Sure, it can handle a plow!
How do I change the oil in my Yamaha Kodiak ATV?
where are all the filters/fittings? What oil should be used?
Also, it starts kind of hard - not as easy as most 4 stroke ATV's. What could be the problem?
It's a 2004|||Go under the four wheeler and on the bottom of the engine towards the rear of it is a lonely bolt. I can't remember the size its either a 17,19, or 21 mm socket. When you pull this oil will go everywhere so be sure that you have an oil pan underneath to catch it. After all of that drains you need to screw off the filter which should be on the left side of the engine. You need to get your filter from your Yamaha dealer. Once your done you need to take your new filter and put some oil on the o-ring to be sure to seal it and then screw it onto the engine. Then you need to screw your drain bolt back on and tighten it. After this you need to put some oil in. Near your dip stick should be a number like 2300 cm3 this probably isn't the number on the engine, I just came up with a number because I can't remember the number. Anyways 2300 = 2.3 liters of oil to put back in your motor. Since you put a new filter on you want to put .2 liters extra in there so... If the engine says 2300 put 2.5 liters of oil. After you put oil in you need to start your atv for a few minutes and then shut it off. Wait about 5 minutes and then check your oil and add any if needed. I'm sorry about not knowing the exact numbers. As for the oils that you need to use you need to stick to a motorcycle/atv specific oil, which you can get from your Yamaha dealer. If you use car oil then then something in the oil will cause the clutches to slip. If you don't have a particular brand that you want to use then just stick with Yamaha's Yamalube 20w-40.
As for the starting problem I don't have a clue, my dad's starts up just fine and it's a 2003.|||omg y dont u like ask the people tht u got it from at the ***** store lol
Also, it starts kind of hard - not as easy as most 4 stroke ATV's. What could be the problem?
It's a 2004|||Go under the four wheeler and on the bottom of the engine towards the rear of it is a lonely bolt. I can't remember the size its either a 17,19, or 21 mm socket. When you pull this oil will go everywhere so be sure that you have an oil pan underneath to catch it. After all of that drains you need to screw off the filter which should be on the left side of the engine. You need to get your filter from your Yamaha dealer. Once your done you need to take your new filter and put some oil on the o-ring to be sure to seal it and then screw it onto the engine. Then you need to screw your drain bolt back on and tighten it. After this you need to put some oil in. Near your dip stick should be a number like 2300 cm3 this probably isn't the number on the engine, I just came up with a number because I can't remember the number. Anyways 2300 = 2.3 liters of oil to put back in your motor. Since you put a new filter on you want to put .2 liters extra in there so... If the engine says 2300 put 2.5 liters of oil. After you put oil in you need to start your atv for a few minutes and then shut it off. Wait about 5 minutes and then check your oil and add any if needed. I'm sorry about not knowing the exact numbers. As for the oils that you need to use you need to stick to a motorcycle/atv specific oil, which you can get from your Yamaha dealer. If you use car oil then then something in the oil will cause the clutches to slip. If you don't have a particular brand that you want to use then just stick with Yamaha's Yamalube 20w-40.
As for the starting problem I don't have a clue, my dad's starts up just fine and it's a 2003.|||omg y dont u like ask the people tht u got it from at the ***** store lol
Hey im recently getting my top end rebuilt on my yamaha warrior 350 atv and i was wondering if this is right?
http://www.mototuneusa.com/break_in_secrets.htm
Should I go with the Manufacturer's way of taking it easy on the engine and break it in. Or follow what this guy says and beat on it to break it in?|||Follow the guide,.
Should I go with the Manufacturer's way of taking it easy on the engine and break it in. Or follow what this guy says and beat on it to break it in?|||Follow the guide,.
I have a yamaha banshee ATV from the year 2000 and i lost the key to the beast.....any tips to hotwire it?
yamaha banshee, ATV, year 2000, lost key, how do i hotwire it?|||There should be a number on the ignition itself that is not the VIN that you can take to a shop that cuts bike keys (not all hardware stores do) and they can cut a key based on that number. It will be a little more expensive than copying a key but much cheaper than replacing the ignition.|||With all the new devices they have for security I doubt it. But you should be able to give them the VIN # and get a key made...Unless of course it's hot...then you might have a problem. Even if you get a new ignition...they will probably ask or the Serial Number...(or VIN# same thing) Hope it aint hot. lol|||dude just go buy a new ignition for it.|||theswitch should have a 5 digit code on bottom. You'll need to go to a Yamaha dealer with that number and find a dealer that has a "codecutter" for making duplicate keys. It usually costs ten bucks or if you don't need headlights just unplug the switch. On YFZ350M the keyswitch only shorts out the cdignition to ground when switch is in off position. Now the whole friggen yahoo world can snag yer bike|||Just go back to the dealer that it was purchased at and they should have a # for it and can make you a new key for about $5.00|||Sounds like you stole it, if you have any common sense, go to a dealer and by a new ignition switch.|||no. but you can get a molded for the place it may cost you some $$$$|||Listen to sovereign he knows what hes talking about, take the lock off get the number then go to your dealer and get a duplicate most good agents can do the same for most jap bikes and British too but like he says you need to get security or good insurance on your bike cause these, like a lot of machines are very easy to steal
Does anyone know when the new 2007 yamaha atv's are going to be available?
im looking to see what the new colors are going to be and what them have changed on the quads.|||LATE 2006
What year is my Yamaha Tri Moto 125 Three Wheel ATV?
Im trying to find out the year of my Yamaha Tri Moto 125 three wheel atv. Vin # 3X3-021722|||Nice double post.
once again...your VIN is 17 digits long, and start with a "j"
Like this one: jy321v009fc165834 go find it, and google a yamaha VIN decoder.|||it should be a 1982.
once again...your VIN is 17 digits long, and start with a "j"
Like this one: jy321v009fc165834 go find it, and google a yamaha VIN decoder.|||it should be a 1982.
Where Can I find a wiring diagram for a Yamaha 350 Terrapro Atv ?
1988 Atv Terrapro Yamaha|||It's not a complicated system.
These diagrams are for different models.
But they will give you a basic idea of the circuitry and color codes.
http://www.3wheelerworld.com/WiringYamah鈥?/a>|||I have one that I'll be glad to share with you
These diagrams are for different models.
But they will give you a basic idea of the circuitry and color codes.
http://www.3wheelerworld.com/WiringYamah鈥?/a>|||I have one that I'll be glad to share with you
What is the best engine oil for a 350 Yamaha ATV other than what is available from the dealer.?
The most important factor in oils is the weight. This is actually a measurement of the oils viscosity at different temps. Once you know the required weight you simply need to buy a name brand oil.
All oils are basically the same and despite any advertising you see or hear the difference between one brand over the other is negligible since the only difference between brands is the detergents used by the various manufacturers.
Hope this helps and safe riding.|||any "brand name" 10w30. if you would use in your car, you can use it in the atv.
All oils are basically the same and despite any advertising you see or hear the difference between one brand over the other is negligible since the only difference between brands is the detergents used by the various manufacturers.
Hope this helps and safe riding.|||any "brand name" 10w30. if you would use in your car, you can use it in the atv.
I have a 1998 atv yamaha warrior 350 runs for 5 minutes then won't start what could be the problem?
check the tubing to and from the carburator for blockage, check filters if any, and check the battery, does it hold a charge? if it has one. there could also be a bad wire or fuse.|||I had a bike that did that once. Have the stator checked.
Yamaha ATV fuel air mixture problem problem?
I have a Yamaha Bruin yfm350 quad bike 2005, I've recently dismantled and cleaned my carberetor. Now I've rebuilt it I've discovered there is no guidance in my manual to set the fuel air mixture. From fully set in how many turns out would be a good start, any help would be great please....|||1.5 to 2.0 turns would be a reasonable start off point.|||2 turns out would be a good start|||1 1/2 turn out and 1/4 turn each time after...remember not to go too lean.
best of luck*****
best of luck*****
Question about a yamaha blaster ATV?
On a yamaha blaster, where do the oil injector line go, coming from the crank side on the fourwheeleer.|||Into the right side of the carburetor.
Look on the side of the carb - there will be pipe the same diameter as the oil line (same color and material as the carb).
Look on the side of the carb - there will be pipe the same diameter as the oil line (same color and material as the carb).
What year did yamaha stop making the yamaha warrior 350 atv and make it a yamaha raptor 350?
im buying a warrior/raptor and he says its a 2005 yamaha warrior 350 but i thought they stopped making warriors in 2004 and 05-current is the raptor?|||2004 was the last year Warrior 350 %26amp; 2005 was the first year Raptor 350
I have a yamaha bruin 250 atv that starts fine and idles good but when i give it gas it bogs down?
and backfires out of the carb. i ran some berryman b12 through the carb and it has no effect.|||Backfiring out of the carb is a sign of a leaking intake valve.
When the spark plug fires, the compression of the engine blows the burnt fuel out of the intake valve and through the carburetor.
Tight valve clearances will hold the valves open a fraction.
Adjust the valves|||Spraying Berrymans [good product by the way] or anything else into the carb is pretty much a toxic waste of time. You may have an intake leak, in which case spraying that cleaner around the outside of the intake will identify it. Could be time to remove and disassemble the carb for cleaning. Do some on line searching for a rebuild kit if you can do this yourself.|||try cleaning them.
When the spark plug fires, the compression of the engine blows the burnt fuel out of the intake valve and through the carburetor.
Tight valve clearances will hold the valves open a fraction.
Adjust the valves|||Spraying Berrymans [good product by the way] or anything else into the carb is pretty much a toxic waste of time. You may have an intake leak, in which case spraying that cleaner around the outside of the intake will identify it. Could be time to remove and disassemble the carb for cleaning. Do some on line searching for a rebuild kit if you can do this yourself.|||try cleaning them.
What is a 1998 yamaha 80cc badger atv worth, with a rebuilt motor and new tires?
this was bought new and mantained well, when the motor got weak last year I had it rebuilt, put new back tires on it and all the pastic is in good shape. my son is out growing it and I would like to sell it but don't know what it is worth.|||I sold mine like three years ago to the dealer for 1500...it had paddles and exhaust|||kelly blue book retail value is 1155.00 dollars in perfect condition.
Is 1990 Yamaha warrior ATV parts interchangeable with 2000 warrior parts?
can i replace my 2000 warrior 350 atv rear swing arm and axel sprocket ext with one from a 1990? are they the same parts|||no u cannot and the reason for that is if manufactures made parts that would interchange they would lose money selling replacement parts. that's 1 reason Davidson almost went bankrupt was to many parts were interchangeable
What type of engine oil does a 2004(ATV) Yamaha Bear Tracker 250 use?
And also does it require separate gear oil??|||Buy a repair manual. You will need it eventually for something bigger.|||dk
Sunday, January 1, 2012
I need to find a downloadable service manual for a 1986 Yamaha Moto 4 ATV.?
I have searched online and all I can come up with are websites that want you to buy the manual. I just want to download or view a manual to fix a problem of there being no spark.|||Highly doubtful you will find one. They are dealer only items and anything else you find out there is probably bootleg. Ebay is full of them for cheap.
Who knows a web site to find a free wiring diagram for a 2001 Yamaha ymf350 Wolverine ATV = A four wheeler?
If there is a different category to list this question - please let me know of it.
Thank you to all answers.|||Don't know of a web site but whenever I need any diagrams or good knowledge I go to the Library. Does help living in a good size city I've been able to checkout almost all manuals for like 3 weeks and never not been able to find the answer to what needed fixing.I've rebuilt engines thanks to our Library.Hope that helps.Just fixed a 85 Honda Big Red with help from the library.
Thank you to all answers.|||Don't know of a web site but whenever I need any diagrams or good knowledge I go to the Library. Does help living in a good size city I've been able to checkout almost all manuals for like 3 weeks and never not been able to find the answer to what needed fixing.I've rebuilt engines thanks to our Library.Hope that helps.Just fixed a 85 Honda Big Red with help from the library.
What type of gas do i put in my 2004 yamaha raptor 50 ATV?
do i premix it or? what types of liquids do i need to keep it is good running order?|||Here's a 7 year old on his http://www.youtube.com/watch?v=ISQ9yd0sd鈥?/a>
It's a 4 stroke not a 2 stroke.
Oil mix is 2 stroke.
Learn what the difference is.
It's a 4 stroke not a 2 stroke.
Oil mix is 2 stroke.
Learn what the difference is.
How much horsepower would a fuel jet kit give an atv, ie. Yamaha 660R atv?
zero.. you first need to put on an exhaust and air filter. a jet kit is used to tune the carb after these items are installed
How hard is it to replace a starter clutch on a 2001 yamaha 350 warrior atv?
Is this a backyard job or is it very technical in nature. Are there any links to step by step how to?|||Not very difficult job. But the work area has to be clean! If you get sand or dirt inside you will destroy everything after very short time.|||A special tool is required to remove the flywheel.
http://www.motionpro.com/motorcycle/part鈥?/a>
A quality torque wrench is necessary when installing the flywheel.
A service manual will be needed to learn the torque specs.
http://www.motocom.com/motorcycles/
http://www.motionpro.com/motorcycle/part鈥?/a>
A quality torque wrench is necessary when installing the flywheel.
A service manual will be needed to learn the torque specs.
http://www.motocom.com/motorcycles/
What is the stock horsepower rating of an 87 yamaha warrior 350 atv and a 2007 yfz 450 atv.?
Im just looking for some numbers for performance comparison and if anyone know if the alba motorsports high comp. piston and .450 cam kit what the gains are from the kit for the yamaha warrior|||18 hp
What atv is overall better an kawasaki's bruteforce 750i or yamaha grizzly 700 fi no eps?
i am 15 years old goin on 16 and ive been saving up for a new atv i now have a yamaha moto4 225 and i was wondering what atv is overall better kawasaki bruteforce 750i or yamaha grizzly 700 fi no eps.|||i like kawasaki. they have been more reliable to me.
Electrical prob with atv yamaha warrior when i press the start button the relay switch clicks?
if thats not clickin the solenoid is sometimes if i move the electrical stuff around it will just work but if i ride it for a little bit it wont work again and today it just suddenly worked for no reason and i put a new bat in a couple weeks ago but the wiring and stuff looks pretty coroded the stuff unfroze wen it started workin wat could it be|||when a relay clicks real loud that usually means your gonna need a new relay. sometimes you can clean them, but most the time it means its burnt.
you may want to check your corroded wires before replacin the relay though. a funky ground will cause the same thing:)
you may want to check your corroded wires before replacin the relay though. a funky ground will cause the same thing:)
Subscribe to:
Posts (Atom)